CUSTOMER DRAWING Product Product Dimensions Cable Dimensions Description A B L D E F G J MIN MIN MAX MAX MIN MIN MAX 2.50 3.00 24.50 3.00 1.50 1.00 2.50 7.000.50 CWT-3-W122-5 (0.098) (0.118) (0.965) (0.118) (0.059) (0.040) (0.098) (0.2760.020) 4.30 4.80 29.30 4.80 2.00 1.50 4.30 9.000.50 CWT-5-W122-5 (0.169) (0.189) (1.154) (0.189) (0.079) (0.059) (0.169) (0.3540.020) 6.00 6.70 32.00 6.70 3.30 2.80 6.00 10.00 0.50 CWT-6-W122-5 (0.236) (0.264) (1.260) (0.264) (0.130) (0.110) (0.236) (0.3940.020) 6.40 7.30 32.50 7.30 3.30 2.80 6.40 11.001.00 CWT-7-W122-5 (0.252) (0.287) (1.280) (0.287) (0.130) (0.110) (0.252) (0.4330.040) 8.70 9.20 35.50 9.20 4.50 4.00 8.70 12.00 1.00 CWT-9-W122-5 (0.343) (0.362) (1.398) (0.362) (0.177) (0.157) (0.343) (0.4720.040) 10.00 11.50 35.50 11.50 4.50 4.00 10.00 13.001.00 CWT-11-W122-5 (0.394) (0.453) (1.398) (0.453) (0.177) (0.157) (0.394) (0.5120.040) 13.00 15.00 45.50 15.10 7.00 6.50 13.00 17.001.00 CWT-13-W122-5 (0.512) (0.591) (1.791) (0.594) (0.276) (0.256) (0.512) (0.6690.040) MATERIALS 1. INSULATION SLEEVE: Transparent heat-shrinkable radiation cross-linked modified polyolefin. 2. SOLDER PREFORM WITH FLUX: SOLDER: TYPE Cd18 per ANSI/J-STD-006. FLUX: TYPE ROM1 per ANSI/J-STD-004. 3. MELTABLE SEALING RING: Thermally stabilized thermoplastic. 4. GROUND LEAD: Raychem cross-linked polyethylene wire, AWG22, stranded tin plated copper. Color: green. APPLICATION 1. These controlled soldering devices are designed for termination of a bare or tin-plated copper shield on a cable having an insulation rated for at least +85q C, meeting the dimensional criteria listed in the table above. 2. Temperature range: -55q C to +125q C. 3. When installed properly, these devices will meet the requirements of TE Connectivity/Raychem Specification RT-1404. 4. For installation procedure and application equipment, consult TE Connectivity /Raychem RPIP 824-00. For best results, prepare the cable as shown: TITLE: SOLDERSLEEVE TERMINATOR WITH PRE-INSTALLED LEAD Unless otherwise specified dimensions are in DOCUMENT NO.: millimeters. Inches dimensions are shown in brackets Raychem DIMENSIONING AND TOLERANCING PER GPS Devices (ISO STANDARDS) CWT-XX-W122-5 ANGLES: 030 TOLERANCES: Tyco Electronics Corporation reserves the right to amend this drawing at any REV: DATE: 0.00 0.02 MM ROUGHNESS time. Users should evaluate the C May 9, 2012 0.0 0.2 MM IN MICRON suitability of the product for their 0 0.5 MM application. PREPARED BY: CAGE CODE: ECO NUMBER: SCALE: SIZE: SHEET: YNGUYEN 06090 NTS A 1 of 1 ECO-12-008844 2003-2012 Tyco Electronics Corporation. All rights reserved. If this document is printed it becomes uncontrolled. Check for the latest revision.