CUSTOMER DRAWING ADHESIVE OUTER SLEEVE PRODUCT DIMENSION CONDUCTOR MASS PART COLOR I.D. (A) Cut Length (B) Wire O.D. (Note*) KG/1000 pieces DESCRIPTION CODE Adhesive Sleeve Adhesive Sleeve Min Max Min Max .05 (.002) .05 (.002) 1 .5 (.06) 1 .5 (.06) D-150-C-11 Green 1.11 (.044) 2.29 (.090) 21.75 (.86) 19.05 (.75) 0.80 (.031) 1.10 (.043) 0.165 0.202 D-150-C-12 Red 1.68 (.066) 2.74 (.108) 21.75 (.86) 19.05 (.75) 1.10 (.043) 1.50 (.059) 0.198 0.242 D-150-C-13 Blue 2.13 (.084) 3.43 (.135) 21.75 (.86) 19.05 (.75) 1.50 (.059) 2.30 (.090) 0.261 0.319 D-150-C-14 Yellow 3.34 (.133) 4.80 (.189) 21.75 (.86) 19.05 (.75) 2.30 (.090) 2.80 (.110) 0.332 0.405 MATERIALS 1. MELTABLE ADHESIVES: Environment resistant modified thermoplastic fluoroelastomer. Color coded 2. OUTER SLEEVE: Heat-shrinkable, transparent, radiation cross-linked modified fluoropolymer. Color coded APPLICATION 1. These parts are designed to provide an environment resistant to repair damaged primary wire that have a radial crack up to 360 degrees, nicks/scrapes not longer than on the insulation rated for 135 C minimum and no damage to wire conductor. For insulations procedures refer to RPIP 1101. 2. Install using Tyco Electronics approved convection or infrared heating tools in accordance with Tyco Electronics. When installed with approved convection or infrared heating tools, assemblies will meet the performance requirements of TE D-6201 spec. Infrared tools are not recommended for use with black cable jackets. 3 Temperature range: -65 C to +180 C. Product will withstand continuous temperature of 150 C for a period of 500 hours, and continuous temperature of 180 C for a period of 168 hours. NOTE*: If the O.D. of wire is out of the range that is specified in Table, use the next size of C-Wrap up or down. WIR E O D TITLE: SIDE ENTRY REPAIR SLEEVE IMMERSION RESISTANT, 150 DEG C, RoHS COMPLIANT C-WRAP DOCUMENT NO.: Unless otherwise specified dimensions are in Raychem millimeters. Inches dimensions are shown in brackets Devices D-150-C-1X ANGLES: 030 TOLERANCES: Tyco Electronics Corporation reserves the right to amend this drawing at any REV: DATE: 0.00 0.02 MM ROUGHNESS time. Users should evaluate the March 14, 2013 0.0 0.2 MM C1 IN MICRON suitability of the product for their 0 0.5 MM application. PREPARED BY: CAGE CODE: ECO NUMBER: SCALE: SIZE: SHEET: TNGUYEN 06090 ECO-13-004675 NTS A 1 of 1 2013 Tyco Electronics Corporation. All rights reserved. If this document is printed it becomes uncontrolled. Check for the latest revision. X-ON Electronics Largest Supplier of Electrical and Electronic Components Click to view similar products for Solder Sleeves & Shield Tubing category: Click to view products by TE Connectivity manufacturer: Other Similar products are found below : 899170-000 620040N001 620069N003 CTA-0050-01 629624-000 6500750004 6501390002 CX0781-000 696396-000 697080-000 D-150- 0331CS2902 D-181-1222-90/9CS2800 D-300-01CS1108 715325N001 908357N001 982127-1 D-436-0182CS246 D-436-37CS2651 D-436- 61CS246 D-436-82-CS2621 D-659-0087 E53797N001 CB0213-000 CB0219-000 S200-2-01 S200-4-00CS2904 LSS-81-16AA-CS5575 ST18-2-00 FLX40-020-04-CS8651 325534-000 CTA-0025 D-108-07CS436 D-128-0010 D-141-0108CS404 D-144-41CS1371 D-150-0231- NRCS2896 D-150-1011 395947-000 427243N001 B-801-18-01 515-9 C67137-000 CB0220-000 D-436-0185CS1102 D-436-36CS2908 D- 436-37CS2908 D-436-52CS246 D44133N001 LSS-26-8A 626168-000