JMSCT-5XP TE Connectivity

CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) MST MST Sensitive TO-5 Diode Suppressed/ Transistor Driven High Performance Relay Qualified to MIL-R-28776/3 + X2 X1 XB A2 B2 A1 B1 A3 B3 Terminal View Product Facts n Transistor driver & suppression diode n Hermetically sealed n High shock & vibration ratings n Spreader pads n Excellent RF switching Electrical Characteristics Contact Ratings Contact Arrangement Contact Operations Type Load Min. 2 Form C (DPDT) 1.0 A 28 Vdc Resistive 100,000 Contact Material 250 mA 115 Vac, 60 Hz & 400 Hz Resistive (case not grounded) 100,000 Stationary Gold/platinum/palladium/silver alloy 100 mA 115 Vac, 60 Hz & 400 Hz Resistive 100,000 (gold plated) 0.2 A 28 Vdc Inductive (0.32 Henry) 100,000 Moveable 0.1 A 28 Vdc Lamp 100,000 Gold/platinum/palladium/silver alloy 30 A 50 mVdc Low Level 1,000,000 (gold plated) 0.1 A 28 Vdc Intermediate Current 50,000 Contact Resistance Before Life 100 milliohms max. (measured 10 mA 6 Vdc) After Life 200 milliohms max. (measured 1 A 28 Vdc) .335 (8.51) DIA MAX Mechanical Life Expectancy 1 million operations .370 (9.40) DIA MAX Coil Voltage 5 to 48 Vdc .031 .003 (0.79) .375 (9.53) Coil Power 565 mW max. 25C .035 (0.89) MAX Duty Cycle Continuous TRANSISTOR Pick-up Voltage Approximately BASE CONNECTION 50% of nominal coil voltage TERMINALS W 1.500 MIN (38.1) Pick-up Sensitivity C .500 MIN (12.7) 60 mW max. 25C P .187.010 (4.75.25) .200 (5.08) (Length excludes mounting pad) 36 3 DIA GROUND PIN (OPTIONAL) Header OPTIONAL PINS +.002 .017 (0.43) DIA -.001 .370 (9.40) DIA MAX Enclosure 1-24 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.CII Low Signal Relays CII Low Signal Relays Double Pole, Electrically Held, 1 Amp and Less (Continued) Operating Characteristics Environmental Characteristics Semiconductor Characteristics MST (Continued) Timing Temperature Range Diode Operate Time 4.0 ms max. -65C to +125C 100 Vdc peak inverse voltage (PIV) 1 Release Time 7.5 ms max. 1.0 Vdc max. transient voltage Weight Contact Bounce 1.5 ms max 0.12 oz. (3.40 grms) Transistor Dielectric Withstanding Voltage 0.13 oz. (3.45 grms) with spreader pad 0.3 Vdc min. base turn off voltage Between Open Contacts attached 6.0 Vdc min. emitter-base breakdown 500 Vrms 60 Hz voltage (BV ) 25C Vibration Resistance EBO Between Adjacent Contacts 80.0 Vdc min. collector-base breakdown 30 Gs, 10 to 3,000 Hz 500 Vrms 60 Hz voltage (BV ) 25C & I =100 A CBO C Shock Resistance Between Contacts & Coil 75 Gs, 6 1 ms max. 500 Vrms 60 Hz QPL Approval Insulation Resistance MIL-R-28776/3 (JMST) 10,000 megohms min. 500 Vdc 1,000 megohms 500 Vdc (coil to case +125C) .103 (2.62) .156 (3.96) .014 .003 (0.36) .370 (9.40) SQ MAX .395 (10.03) SQ MAX 0.47 (1.19) DIA .100 (2.54) .150 (3.81) .100 (2.54) .100 (2.54) .140 .175 DIA (3.56 4.45) S S2 W Spreader & Mounting Pads Coil Data Coil Pickup Pickup Drop-Out Drop-Out Nom. Coil Circuit Coil Circuit Base Turn Base Turn Nom. Coil Resistance Voltage Voltage Voltage Voltage Max. Coil Current Current On Current On Current Power Coil in Ohms Vdc (Max.) Vdc (Max.) Vdc (Min.) Vdc (Min.) Coil Voltage mA (Max.) mA (Min.) mA (Max.) mA (Max.) (mW) Desig. 10% 25C 25C 125C 25C -65C Voltage (Vdc) (Note 1&2) (Note 1&2) 25C 125C 25C (Note 1) (Note 2) (Note 2) (Note 2) (Note 2) MST 5.0 100 59.3 43.5 2.8 0.37 3.6 1.50 0.22 0.14 250 7.0 5 6.0 200 35.4 26.4 3.8 0.25 4.8 1.00 0.28 0.18 180 10.0 6 9.0 400 25.8 19.7 5.2 0.18 7.8 0.75 0.54 0.35 203 15.0 9 12.0 850 16.7 12.2 7.4 0.12 11.0 0.47 0.63 0.41 169 20.0 12 18.0 1,600 13.1 9.7 10.0 0.09 14.5 0.38 0.91 0.59 203 30.0 18 26.5 3,300 9.5 6.9 14.2 0.06 19.0 0.24 1.37 0.89 213 40.0 26 36.0 6,500 6.4 4.8 20.0 0.034 27.0 0.17 1.80 1.25 199 57.0 36 48.0 11,000 5.1 3.7 25.8 0.026 36.0 0.13 2.40 1.60 209 75.0 48 Notes: 1. Coil resistance not directly measurable. Coil current should be within limits shown when tested at nominal voltage at 25C for 5 seconds max. 2. Set base current at 3 mA to 15 mA during measurements. Ordering Instructions Catalog-selected Relays: The catalog number is derived by choosing the proper CODE for each of the relay characteristics in the order in which the codes are listed. Specifying a Part Number Example: Type Terminal Diodes Ground Pins Coils Spreader/Mounting Pads MS CT G -26 S * The part number example shown on this page is for catalog items. For a list of specific QPL part numbers, please see the index in Section 15. 1-25 Catalog 5-1773450-5 Dimensions are shown for Dimensions are in millimeters USA: +1 800 522 6752 For additional support numbers Revised 3-13 reference purposes only. unless otherwise specified. Asia Pacific: +86 0 400 820 6015 please visit www.te.com Specifications subject UK: +44 800 267 666 www.te.com to change.