xx Operating Information Standard Accessories Item Description The TPP0850 Probe is a high impedance probe Crocodile clip WARNING. Do not substitute accessories from other with 50X attenuation that is designed for use with products for use with this probe. Only use the Attach the clip to the banana Tektronix DPO/MSO4000B & DPO/MSO5000 series accessories that are included with this probe. end of the common lead and ground-referenced oscilloscopes. then to your circuit common. To avoid electric shock when using the probe or Connect theprobeasshownintheillustrationsbelow. accessories, keep your ngers behind the nger guard oftheprobebodyand awayfromtheshaded area shown in the accessory illustrations below. Reorder Tektronix part number 344-0461-xx Item Description Common spring(TACS) Small hook tip (TASH) Use this accessory to limit Use this tip to access test aberrations on high frequency points in tight spaces. Screw signals caused by common the hook tip onto the probe tip lead path inductance. and then clamp the hook onto Bend the spring to reach the circuit. nearby common connections Rating: 1000 V CAT II (~1 in). Note: Only the 1000 V CAT II rating is applicable when used TPP0850 Reorder Tektronix part number with the TPP0850 probe. 214-5299-xx 800 MHz 50X High Voltage Probe Color bands Reorder Tektronix part number Instructions Use these bands to identify 013-0388-xx CompensatingtheProbe (Required for Initial Use) the oscilloscope channel at the You must compensate the probe after you attach it to an Large hook tip (TALH) probe head. oscilloscopeforthersttime,orafteryoumoveittoanother Screw the hook tip onto the channel on the same oscilloscope. probe tip and then clamp the hook onto the circuit. 1. Connecttheprobe toanoscilloscopechannel. Rating: 1000 V CAT II 2. On MSO/DPO5000 instruments: Note: Only the 1000 V CAT II Reorder Tektronix part number rating is applicable when used a. Connect the probe to the probe compensation output with the TPP0850 probe. 016-1886-xx (5 pairs) terminals on the oscilloscope front panel. b. Select Vertical > Probe Cal.... Optional Accessories c. Selectthechannelnumber tabofthechannelthatyou Reorder Tektronix part number The accessories shown below are available for the probes connected the probe to. 013-0389-xx andare rated 30 Vunlessindicatedotherwise. d. IntheCalibrationsection,clickCalibrateProbe. Commonleads (6 in and 18 in) (TACL) On MSO/DPO4000B instruments: Part Slide the lead over the probe Accessory number a. Press the Channel Menu front panel button for the head and snap it into place. channel that you connected the probe to. BNCtoTipAdapter, 013-0291-xx Connect the banana plug Unterminated b. PushtheMorebuttonuntilProbeSetupisselected. end directly to your circuit common, or use the crocodile Rubber Spring Tip 206-0060-xx c. Push the Calibrate Probe button and follow the clip included with the probe. on-screen instructions. Reorder Tektronix part Probe Holder TPH1000 If the probe compensation fails, verify that the signal numbers: and ground connections are secure at the Probe Comp 6 inch: 196-3526-xx connections on the oscilloscope, and secure at the probe 18 inch: 196-3527-xx head and tip. *P071288402* x 071-2884-02Specications Avoid Electric Overload. To avoidinjuryorre hazard, do Characteristics Description not apply potential to any input, including the reference Table 1: Electrical and mechanical specications Pollution Do not operate in environmentswhere cond- inputs, thatvariesfromgroundbymorethanthemaximum Degree 2 uctive pollutants may be present(asdened in rating for that input. Bandwidth (3 dB) 800 MHz IEC 61010-1). Rated for indoor use only. System rise time (typical) <525 ps Additional UL61010-031 2010 Avoid Exposed Circuitry and Do not Operate Without Safety CAN/CSA C22.2 No. 61010-031:07/A1:2010 Covers. Donottouchexposedconnectionsandcomponents System input capacitance 1.8 pF Standards IEC61010-031 IEC 61010-031/A1:2008 (typical) when power is present. EquipmentRecycling. This product complies Systemattenuation accuracy 50:1 2.2% Inspect The Probe And Accessories. Before each use, with the European Unions requirements inspect probe and accessories for damage (cuts, tears, Systeminputresistance DC 40 M 1% according to Directive 2002/96/EC on waste defects in the probe body, accessories, cable jacket, etc.). electrical and electronic equipment (WEEE). Propagation delay ~6.1 ns Do not use if damaged. For more information about recycling options, Cable length 1.3 m check the Support/Service section of the Do Not Operate in Wet/Damp Conditions. Maximuminputvoltage 1000 V CAT II (2500 V ) Tektronix Web site (www.tektronix.com). RMS pk Do Not Operate in an Explosive Atmosphere. (seePerformanceGraphs) Table 2: Environmental specications Keep Product Surfaces Clean and Dry. Safety Summary Safety Terms and Symbols Terms inThis Manual. Performance Graphs Reviewthefollowingsafetyprecautionstoavoidinjuryand Characteristics Description These terms may appear in this manual: prevent damage to this product or any products connected Temperature to it. To avoid potential hazards, use this product only as WARNING. Warning statements identify conditions or Operating 0Cto+50C(+32Fto+122F) specied. Using the probe or accessories in a manner not practices that could result in injury or loss of life. Nonoperating 40 C to +71 C (40 F to +160 F) specied couldresult ina shockorre hazard. Humidity CAUTION. Caution statements identify conditions or To Avoid Fire or Personal Injury practices that could result in damage to this product or Operating 5% to 95% relative humidity (RH) up to other property. Ground-Referenced Oscilloscope Use. Do not oat the +30 C common lead of this probe when using with ground 5% to 75% RH above +30 C to +50 C. Symbols on the Product. These symbols may appear on Noncondensing referenced oscilloscopes (for example, DPO, MSO, and the product: TDS series oscilloscopes). The common lead must be Nonoperating 5% to 45% RH +65 C to +85 C. connected to earth potential (0 V). Noncondensing Altitude ConnectandDisconnectProperly. Connecttheprobeoutput tothemeasurementinstrumentbeforeconnectingtheprobe Operating 3.0 km (9,842 ft) maximum to the circuit under test. Disconnect the probe input and Nonoperating 15.4 km (50,000 ft) maximum the probe common lead from the circuit under test before disconnectingtheprobefromthemeasurementinstrument. Contacting Tektronix Table 3: Certications and compliances Web site: www.tektronix.com AvoidElectric Shock. Toavoidinjuryorlossoflife,donot Characteristics Description connect or disconnect probes or test leads while they are Phone: 1-800-833-9200 connected to a voltage source. EC Compliance wasdemonstrated to the following Address: Tektronix, Inc. Declaration specication as listed in the Ofcial Journal of Department or name (if known) ObserveAllTerminalRatings. Toavoidreorshockhazard, of the European Communities: 14200 SW Karl Braun Drive observe all ratings and markings on the product. Consult Conformity Low Voltage Directive 2006/95/EC: P.O. Box 500 the product manual for further ratings information before EN61010-031/A1: 2008 Beaverton, OR 97077 USA making connections to the product. Measurement CAT III: Distribution-level mains, xed Email: techsupport tektronix.com Whenusingprobeaccessories,never AvoidElectricShock. Category installation exceed the lowest rating of the probe or its accessory, Product CATII: Local-level mains, appliances, portable Warranty Information whicheveris less,includingthemeasurement categoryand Examples equipment voltage rating. For warranty information, go to CATI:Circuitsnotdirectlyconnectedtomains. www.tektronix.com/warranty. CopyrightTektronix,Inc. Allrightsreserved. www.tektronix.com