Precision High-Voltage Thick Film Resistors ALED IAMOND SPIR K FILM ELEMENT THIC CGH Series (EAT CONDUCTING ATE AMIC SUBSTR CER 1/4 watt to 5 watt XY COATED BODY %PO TCR of 50 or 100 ppm/C (IGH CONDUCTIVITY 100K ohm to 2000 megohm range 0.5%, 1%, 2% or 5% tolerance ELDED CAP AND LEAD CONSTR LL W UCTION 4IN ,EAD ELECTROPLATED LEADS Electrical Data Power Rating Voltage Rating Resistance Tolerance Maximum TCR 5 IRC Type VCR (ppm/V) 4 4 at 70C (watts) (volts) Range (ohms) (%) (ppm/C) CGH - 1/4 1/4 750 100K - 100M CGH - 1/2 1/2 1,500 100K - 500M CGH - 1 1 3,000 50K - 750M .5, 1, 2, 5 50, 100 0 - -5 CGH - 2 2 5,000 100K - 1500M CGH - 3 3 10,000 200K - 2000M CGH - 5 5 20,000 300K - 2000M Notes: 1. For power rating above 70C, see derating curve. 2. Voltage rating shown is the rated DC continuous working voltage or the sine-wave RMS absolute maximum voltage at commercial line fre- quency. For DC applications the absolute maximum permissible voltage is 1.5 times the value shown for low repetition short-time-overload or pulse conditions of 10 seconds or less duration. 3. Contact factory for higher resistance values. 4. For CGH-1 and 2 above 500 meg and CGH-3 and 5 above 1000M only 2 and 5% tolerance and 100 ppm/C TCR available. 5. Typical voltage coef cient of resistance is -1 to -2 ppm/V measured at fulll rated voltage and 10% rated voltage. Power Derating Curve Temperature Rise Chart 100 100 90 CGH 1/4 90 80 CGH 2-3 80 70 CGH 1/2 70 60 CGH 5 60 50 CGH 1 50 40 40 30 30 20 20 10 10 0 0 80 100 120 140 160 180 0 10 20 30 40 50 60 70 80 90 Ambient Temperature (C) Temperature Rise (C) General Note IRC reserves the right to make changes in product speci cation without notice or liability. All information is subject to IRCs own data and is considered accurate at time of going to print. A subsidiary of TT electronics plc Wire and Film Technologies Division 4222 South Staples Street Corpus Christi Texas 78411 USA Telephone: 361 992 7900 Facsimile: 361 992 3377 Website: www.irctt.com CGH Series Issue June 2009 Sheet 1 of 3 % of Rated Power % of Rated PowerPrecision High-Voltage Thick Film Resistors Environmental Data Maximum R Test Condition Typical R (3) Temperature Shock 0.25% 0.10% Short-Time Overload (1.5 times rated V for 10 sec) 0.20% 0.10% Solder Effect 0.015% 0.05% Terminal Strength 0.20% 0.05% Moisture Resistance (no load or polar) 0.50% 0.20% Load Life (1000 hours at 70C) 1.00% 0.25% Shelf Life (1 year at 25C) 0.10% 0.03% 0.75% 0.30% High-Temperature Exposure (150C for 2000 hours) (175C for 2000 hours) 0.01% 0.40% 2000 VDC, 1500 VAC Dielectric Breakdown (1/4 and 1/2 watt size) (1 watt through 5 watt size) 3500 VDC, 2500 VAC 4 Dielectric Strength 0.15% 0.05% 9 11 Insulation Resistance at 500 VDC 10 ohms typ. 10 ohms typ. Notes: 1. Test method per MIL-STD-202 unless otherwise indicated. 2. Typical de ned as that percent change which will include a minimum of 50% of the measured changes in resistance from a variety of lots representing various unit sizes and ranges. 3. Values shown are the maximum safe dielectric voltage applied from a V block or foil wrapping which extends the complete body length of the resistor under test. 4. Percent change after the maximum safe dielectric voltage is applied for 1 minute. Wire and Film Technologies Division 4222 South Staples Street Corpus Christi Texas 78411 USA Telephone: 361 992 7900 Facsimile: 361 992 3377 Website: www.irctt.com CGH Series Issue June 2009 Sheet 2 of 3