GCR1206EW-150RFT3

Resistors Glueable Chip Resistor GCR Series Suitable for conductive adhesive Planar and wraparound versions High temperature operation to 200C Non-magnetic (G, P & EW types) Range 0805 to 2512 at 1R0 to 10M RoHS compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Data Size 0805 1206 2010 2512 Power 70C W 0.125 0.25 0.625 1 Resistance range ohms 1R0 to 10M Tolerance % 1, 5 LEV V 150 200 400 500 TCR ppm/C <10R:200 10R:100 Operating temperature C -55 to +200 Thermal Impedance C/W 220 160 75 40 Values E24 or E96 preferred - other values to special order Zero-ohm jumper current rating A 1.5 2 Zero-ohm jumper residual resistance milliohms <50 Physical Data Dimensions (mm) & weight (mg) G & P types EW & GW types L W T max A C Wt. 0805 2.00.15 1.250.15 0.6 0.30.15 0.30.1 4.7 T T W 1206 3.20.2 1.60.2 0.7 0.40.2 0.40.15 8.5 A L L W A 2010 5.10.3 2.50.2 0.8 0.60.3 0.60.25 36 Wrap-around terminations (3 faces) 2512 6.50.3 3.20.2 0.8 0.60.3 0.60.25 55 Construction Marking Planar gold G type or P tAg P types: Electrodes, resistor material The components are not marked all data is printed onto the and overglaze are printed onto an alumina substrate. The resistors packaging. are laser trimmed to the required value and protected. Solvent Resistance Wraparound EW type: Thick-film P tAg electrodes, resistor material The component is resistant to all normal industrial cleaning and overglaze are printed onto an alumina substrate. The resistors solvents suitable for printed circuits. are laser trimmed to the required value and protected. The terminations are wraparound coated with a polymer Ag material. Wraparound GW type: These are made as the EW type then plated with a nickel barrier and Gold. All termination styles are suitable for aachmentt t with conductive adhesive. General Note BI Technologies IRC Welwyn TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics own data and is considered accurate at time of going to print. www.ttelectronics.com/resistors TT Electronics plc 03.18Glueable Chip Resistor GCR Series Performance Data Maximum Derating Curve Load at rated power (1000hrs at 70C) R 2% + 0.01 P/Pr Derating from rated power at 70C See Derating Cur ve 100% Short term overload R 1% + 0.01 Dr y heat (1000hrs at 200C) R 2% + 0.01 Damp heat steady state (56 days, 40C, 90% RH) R 1% + 0.01 0 Climatic R 1% + 0.01 70 155 200 Ambienttemperature degC Temperature rapid change (5 cycles -55C to +200C) R 1% + 0.01 Packaging 0805 and 1206 GCR series resistors are supplied on 8mm carrier tape and 7 inch reels as per IEC 286-3, quantity per reel 3000. 2010 and 2512 GCR series resistors are supplied on 12mm carrier tape and 7 inch reels as per IEC 286-3, quantity per reel 2010: 3000pcs 2512: 1800pcs. Ordering Procedure Ordering Procedure Example: GCR1206G-10KFT3 (GCR1206 in gold planar format at 10 kilohms 1%, Pb-free) G C R 1 2 0 6 G - 1 0 K F T 3 1 2 3 4 5 1 2 3 4 5 Type Termination Value Tolerance Packing GCR0805 G Gold planar F = 1% 0805,1206, 3/4 characters T3 Tape, up to 3000/reel 2010 GCR1206 P PtAg planar J = 5% R = ohms GCR2010 EW Polymer Ag wraparound K = kilohms Omit for T18 2512 Tape, up to 1800/reel M = megohms jumper GCR2512 Ni Barrier & Au plated GW R000 = jumper wraparound General Note BI Technologies IRC Welwyn TT Electronics reserves the right to make changes in product specification without notice or liability. All information is subject to TT Electronics own data and is considered accurate at time of going to print. www.ttelectronics.com/resistors TT Electronics plc 03.18