OPB720A-12Z

0.04 to 12 (1 mm to 305 mm) with 90% reflective material. (Typical Maximum detection distance to be set at factory) Recognizes objects as small as 0.08 (2 mm) Ambient light rejection < 100K Lux Open collector output Cable length 39 (990 mm) lead length 28 AWG wire The OPB720A and OPB720B Series reflective switches detects objects as far away as 12 (305 mm) using standard 90% reflective material, and can detect objects as small as 0.08 (2 mm). The OPB720 series consist of three standard reflective switching distances -06Z for typically 6 (152 mm), -12Z for typically 12 (305 mm) and -30VZ for typically 30 (762 mm). The power supply voltage range of the OPB720A series is 10 to 30 volts while the power supply voltage range for the OPB720B is 4 to 7 volts. The OPA720A and OPB720B sensors are NOT affected by ambient light in most conditions. Ambient light conditions are compensated by using a synchronous driver detection scheme. This sensor has a logical output that switches from a high level with reflective target to a low level with no reflective tar get. With the addition of hysteresis, the OPB720 series minimizes output switching oscillations. The type of material used for the target is very dependent on the distance that can be achieved for the sensor. Taking this into consideration, the OPB720 series can be used in either a reflective or interruptive mode. As an example, the OPB720A-12Z can easily be used in a reflective mode for distances around 12 (305 mm) while when reflecting o aff retro -reflective target similar to 3M 3870 or Nippon Crystallite at distances around 85 (216 mm) the device works well in the interruptive mode. See the included charts for typical distances with different reflective material for other versions of the OPB720 series devices. The OPB720 series has an open collector output transistor and power requirements are compatible with most PLCs and TTL gates. Ordering Information Part Number Description Conveyer belt package recognition Maximum detecoti n of 0.04 to 6 (1.0 mm to 152 mm) OPB720A-06Z Personnel movement recognition 39 (991 mm) lead length with 28 AWG wire, using white 90% OPB720B-06Z reefl cvti e paper Near-focus security systems Hand wash and soap dispensing stations Maximum detecoti n of 0.04 to 12 (1.0 mm to 305 mm) OPB720A-12Z 39 (991 mm) lead length with 28 AWG wire, using white 90% Toilet and urinal sensors OPB720B-12Z reefl cvti e paper Product dispensing systems Maximum detecoti n of 0.04 to 30 (1.0 mm to 762 mm) Vcc OPB720A-30VZ 39 (991 mm) lead length with 28 AWG wire, using white 90% OPB720B-30VZ reefl cvti e paper OPB720A-30VZ & OPB720B-30VZ ONLY Electronics Output Addioti nal laser safety information can be found on the Optek website. See applicaoti n 221. Classicfi ation is not marked on the device due to space limitations. See package outline for Ground centerline of optical radiance. Operangti devic- es beyond maximum rating may cause devices Ro HS Pin Description Red V CC White Output Black Ground MILLIMETERS DIMENSIONS ARE IN: INCHES Pin Description Pin Description Pin Description Operating Temperature Range OPB720A Series 0 C to + 50 C Red Vcc White Output Black Ground OPB720B Series 0 C to + 70 C Storage Temperature Range -40 C to + 80 C (1) Lead Soldering Temperature (1/16 (1.6 mm) from case for 5 seconds with soldering iron) 260 C Supply Voltage (V ) CC OPB720A Series 10 to 30 Volts OPB720B Series 4 to 7 Volts Maximum Collector Voltage 30 V Collector DC Current (Sink) 50 mA Power Dissipation 300 mW Low Level Output Voltage V OPB720A Series - - 0.8 V = 10 Volts, Note 4 OL CC V OPB720B Series - - 0.8 V = 4 Volts, Note 4 CC High Level Output Voltage V OPB720A Series 5.0 - - V = 10 Volts, Note 5 OH CC V OPB720B Series 3.5 - - V = 4 Volts, Note 5 CC Notes: (1) RMA flux is recommended. Duration can be extended to 10 seconds maximum when ofl w soldering. (2) Distance for OPB720A-06Z=6 (152 mm), Distance for OPB720A-12Z=12 (305mm), Distance for OPB720A-30VZ=30 (762 mm) (3) OPB720A-30VZ & OPB720B-30VZ are class 1M laser safety device. Do Not look at the device closer than 4 (100 mm) with a magnifying device. (4) R = 10 K, V = V Distance = See Note 2 & 3, (No Target) L CE CC (5) R = 10 K, V = V (90% Reefl cvti e Surface, Kodak EK E152-7798) L CE CC,