Photologic Slotted Optical Switch Right Angle Package Series OPB920DZ Features: Non-contact switching Right Angle Sensor: LED in tower, photosensor in base Choice of output configuration Optical line can be broken in three axis 24 minimum, 26 AWG UL approved wire leads Description: The OPB920 series optical switch consists of an infrared emitting diode (LED) and a photologic sensor . The LED is mounted on the tower with the photologic sensor mounted on the base of a right angle shape package . The L-Shape or right angle package configuration allows for an opaque object to block the light beam from a multitude of directions including the X - axis Y-axis and Z-axis. The optical center line between the emitter and photosensor is at 45 from the mounting base of the device. The OPB920 Series provides optimum flexibility for the design engineer. The engineer can specify the type of TTL output. For example the output can be: TTL totem pole, TTL open collector, either of which can be bueff red or inverted output. All versions have the added stability of hysteresis built into the circuitry. Custom electrical, wire and cabling and connectors are available. Contact your local representative or OPTEK for more information. Part Number Guide OPB920xZ Series Applications: OPB920 Z A = Totem Pole Non-contact interruptive object sensing B = Open Collector Tray-out sensor C = Inverted Totem Pole D = Inverted Open Collector Amusement gaming equipment All versions with 26 AWG wire termination (24 61cm long) Low paper tray sensor Paper sorting equipment Corner sensor Printers Copying machines Door sensor Optical Switch Ro HS General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is sensors ttelectronics.com www.ttelectronics.com considered accurate at time of going to print. Issue C 09/2019 Page 1 TT electronics plc Photologic Slotted Optical Switch Right Angle Package Series OPB920DZ Pin name Wire Color Ano de Red Catho de/G r o und G r een Vout Blu e Vc c W hite Absolute Maximum Ratings (T = 25 C unless otherwise noted) A Storage Temperature -40 C to +85 C Operating Temperature -40 C to +70 C (1) Lead Soldering Temperature (1/16 (1.6 mm) from case for 5 seconds with soldering iron) 260 C Input Infrared LED DC Forward Diode (LED) Current 40 mA DC Reverse Diode (LED) Voltage 2 V (1) Input Diode Power Dissipation 100 mW Output Photologic Supply Voltage, V (not to exceed 3 seconds) 18V CC Voltage at Output Lead (Open Collector Output version) 35 V (2) Output Photologic Power Dissipation 200 mW (3) Total Device Power Dissipation 300 mW Notes: (1) Derate linearly 2.22 mW/C above 25C (2) Derate linearly 4.44 mW/C above 25C (3) Derate linearly 6.66 mW/C above 25C (4) RMA flux is recommended. Duration can be extended to 10 seconds maximum when ofl w soldering. (5) Methanol or isopropanol are recommended as cleaning agents. The plascti housing is soluble in chlorinated hydrocarbons and k eytones. General Note OPTEK Technology, Inc. TT Electronics reserves the right to make changes in product specificaoti n without 1645 Wallace Drive, Carrollton, TX 75006 Ph: +1 972 323 2200 nocti e or liability. All informaoti n is subject to TT Electronics own data and is sensors ttelectronics.com www.ttelectronics.com considered accurate at time of going to print. Issue C 09/2019 Page 2 TT electronics plc