CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount New Super low ESR, impedance and high heat resistance have been obtained by using PXK conductive polymer as electrolyte. Rated voltage range : 2.5 to 16Vdc, Capacitance range : 100 to 560MF Downsized Suitable for DC-DC converters, voltage regulators and decoupling applications used to PXE computer motherboards etc. RoHS Compliant SPECIFICATIONS Items Characteristics Category -55 to +105C Temperature Range Rated Voltage Range 2.5 to 16Vdc Capacitance Tolerance P20% (M) (at 20C, 120Hz) Surge Voltage Rated voltageB1.15V (at 105C) Leakage Current Shall not exceed values shown in STANDARD RATINGS. (at 20C after 2 minutes) Dissipation Factor 0.12 max. (tane) (at 20C, 120Hz) Low Temperature Z(-25C)/Z(+20C) 1.15 Characteristics (Max. Impedance Ratio) Z(-55C)/Z(+20C) 1.25 (at 100kHz) Endurance The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours (F46 : 1,000 hours) at 105C. Appearance No significant damage Capacitance change P20% of the initial value DF (tanE) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value Bias Humidity The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at 60C, 90 to 95% RH for 1,000 hours (F46 : 500hours). Appearance No significant damage Capacitance change P20% of the initial value DF (tanE) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value Surge Voltage The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change P20% of the initial value DF (tanE) 150% of the initial specified value ESR 150% of the initial specified value Leakage current The initial specified value Failure Rate 0.5% per 1,000 hours maximum (Confidence level 60% at 105C) *Note : If any doubt arises, measure the leakage current after following voltage treatment. Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C. DIMENSIONS mm MARKING Terminal Code : A EX) 2.5V330MF W K89A 330 Size Code fD L A B C W P V 2.5 E61 5 5.8 5.3 5.3 5.9 0.5 to 0.8 1.4 F46 6.3 4.5 6.6 6.6 7.2 0.5 to 0.8 1.9 F61 6.3 5.8 6.6 6.6 7.2 0.5 to 0.8 1.9 0.3max. AP0.2 LP0.3 (Note) Note : L+0.1/-0.2 for F46 PART NUMBERING SYSTEM 132645178910 11213 14 15 16 17 18 A P X K A A A A R A A A A M A A A G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 330MF:331, 560MF:561) Taping code Terminal code Voltage code (ex. 2.5V:2R5, 6.3V:6R3) Series code Category Please refer toProduct code guide (conductive polymer type (1/2) CAT. No. E1001K FDP0.5 BP0.2 P CP0.2CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount New STANDARD RATINGS WV Cap Size Leakage current ESR Rated ripple current Part No. (Vdc) (mF) code (mAmax/after 2min.) (momax/20c, 100k to 300kHz) (mArms/105c, 100kHz) 220 F46 300 19 2,780 APXK2R5ARA221MF46G 330 E61 412 16 3,500 APXK2R5ARA331ME61G 2.5 330 F46 700 16 3,500 APXK2R5ARA331MF46G 560 F61 700 16 3,500 APXK2R5ARA561MF61G 180 F46 360 19 2,780 APXK4R0ARA181MF46G 4 220 E61 440 17 3,390 APXK4R0ARA221ME61G 390 F61 780 17 3,390 APXK4R0ARA391MF61G 150 F46 472 19 2,780 APXK6R3ARA151MF46G 180 E61 567 17 3,390 APXK6R3ARA181ME61G 6.3 220 F46 700 18 3,200 APXK6R3ARA221MF46G 330 F61 1,040 17 3,390 APXK6R3ARA331MF61G 16 100 F61 320 24 2,490 APXK160ARA101MF61G (2/2) CAT. No. E1001K