Non EMC Subracks CATALOG 128 CATALOG 128.qxd 4/24/2014 10:13 AM Page 37 tm Non EMC DIN-Based VectorPak Subracks Rack Components & Accessories Adapter Plates (Z-Rail Type) Part No. Description AS1/2 Adapter plate for mounting DIN connectors directly onto subrack, 84 tapped holes (2.5mm x 4.5mm pitch) Adapter Plate (Pkg of 2) To be used without backplane Insulation Strips Mounted between backplane and rear extrusion Rear Extrusion 5250238 Part No. HP Width 5250998-84 84 17.00 (431.8mm) Insulation Strip 5250998 Nut Strips Threaded mounting holes spaced at 0.2 centers slide into extrusion grooves, can be used to anchor panels, cards or other components. Used on front & rear extrusions on all Vector DIN based metric subracks. Nut Strip Part No. HP Width 5250268-84 or 5250268-84 84 17 (431.8mm) 5700202 5250268-63 63 12.8 (325.1mm) 5250268-42 42 8.6 (218.4mm) 5250268-21 21 4.4 (111.8mm) .265W .062 thick .200 Extrusions Front All extrusions available in any length Part No. HP A 5250236-84 84 17.00 (431.8) 5250236-63 63 12.80 (325.8) 5250236-42 42 8.60 (218.4) 5250236-21 21 4.40 (11.8) Pack of 12 8-32 screws, P/N HD94 Rear Part No. HP A 5250238-84 84 17.00 (431.8) 5250238-63 63 12.80 (325.8) 5250238-42 42 8.60 (218.4) 5250238-21 21 4.40 (11.8) Pack of 12 8-32 screws, P/N HD94 Rear Center Part No. HP A 5250237-84 84 17.00 (431.8) 5250237-63 63 12.80 (325.8) 5250237-42 42 8.60 (218.4) 5250237-21 21 4.40 (11.8) Pack of 12 8-32 screws, P/N HD94 Part No. HP A 5250229-84 84 17.00 (431.8) 5250229-63 63 12.80 (325.8) 5250229-42 42 8.60 (218.4) 5250229 -21 21 4.40 (11.8) Pack of 12 8-32 screws, P/N HD94 37 800-423-5659 www.vectorelect.com8 6 5 4 2 1 7 3 REVISIONS ZONE REV. DESCRIPTION APPROVED DATE ALL B D D +.000 17.000 -.010 .200 83 EQ SP .200 =16.600 C C TAP M2.5 x 0.45-6H 84 PL960 .834 6 x .120 .197 3.400 3.400 3.000 3.400 3.400 B B SOLD IN 17.000 LENGTH TO BE CUT TO SIZE VECTOR P/N AS1/2 (pkg of 2) 11115 VANOWEN ST., NAME DATE UNLESS OTHERWISE SPECIFIED: NORTH HOLLYWOOD, CA 91605 DIMENSIONS ARE IN INCHES DRAWN TRUSHAR 01/13/09 TOLERANCES: A A CHECKED FRACTIONAL ANGULAR: .5 DIN ADAPTER PLATE ENG APPR. TWO PLACE DECIMAL .02 THREE PLACE DECIMAL .005 VME CARD CAGE MFG APPR. PROPRIETARY AND CONFIDENTIAL INTERPRET GEOMETRIC 3. REMOVE ALL BURRS & SHARP EDGES Q.A. TOLERANCING PER: THE INFORMATION CONTAINED IN THIS SIZE DWG. NO. REV 2. FINISH: ZINC PLATE PER ASTM-B-633, CLASS 3, TYPE I DRAWING IS THE SOLE PROPERTY OF THIRD ANGLE PROJECTION VECTOR ELECTRONICS & TECH., INC. ANY MATERIAL 1 1. MAT L: STEEL, COLD ROLLED, 16 GA. REPRODUCTION IN PART OR AS A WHOLE B 5700201 B WITHOUT THE WRITTEN PERMISSION OF FINISH 2 VECTOR ELECTRONICS & TECH., INC. IS NOTES: UNLESS OTHERWISE SPECIFIED. SCALE: 2:3 WEIGHT: SHEET 1 OF 1 PROHIBITED. DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1