8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. 1 RELEASED PER E050350 LEK 11/16/05 EF F F 2 REVISED PER E091652 JS 09/11/09 REJH 4-40 UNC-2B COLD FORM TAP 3 REDRAWN PER E100871 DCS 6/28/10 KUK .140 DP MIN. FROM FAR SIDE DO NOT BREAK THRU (6) PL. E E 2.22 2.000 D D .110.010 1.800 .910 .50 3.600 4.600 C C .90 .005 B B .190 .100 .010 MATL TO BE REMOVED SWD DRAWN DATE VICOR NOTES: P.E.IENI 06/30/05 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. UNLESS OTHERWISE SPECIFIED 2. REMOVE ALL BURRS AND SHARP EDGES. MATERIAL HS CFG, .90H, X-FLOW, DIMENSIONS ARE INCH MM 3. CLEAR FINISH, RoHS COMPLIANT, CHROMIUM FREE PER CST-0001 LATEST REVISION. TOLERANCES ARE: SEE NOTES DECIMALS ANGLES LOW FLOW, THREADED A A X.XX X.X = 0.01 0.25 1 4. DENOTES CRITICAL CHARACTERISTICS FOR LOT INSPECTION. X.XXX X.XX = 0.005 0.127 5. DIMENSIONS ARE INCHES ONLY. SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30196 3 SCALE 2 : 1 SHEET 1 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 OF 2 F F E E 3 1.5 EACH SIDE OF VERT 1.756 SEE DETAIL A A R.035 D D R.018 .024 .910 (2) PL034 .215 .200 .035 .110 .040 * .086 R.035 R.010 .080 (10) PL. (30) PL. (2) PL. (14) PL. * .212 * 1.408 * .084 R.030 C C .748 (12) PL. (2) PL. (6) PL. * .217 (3) PL187 +.020 .017 4.600 -.000 (2) PL. C L * .086 B B DETAIL A SCALE 4 : 1 PROFILE COMMON FOR 30196 30723 NOTES: 1. MATL ALUMINUM 6063-T5 SWD DRAWN DATE VICOR 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. JSARIPELLA 9/11/09 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS. 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. UNLESS OTHERWISE SPECIFIED MATERIAL HS CFGA , .90H, X-FLOW, LOW DIMENSIONS ARE INCH MM 5. WORKMANSHIP STANDARDS WS-0004, WS-0006, AND WS-0007 APPLY TO THIS PART. TOLERANCES ARE: SEE NOTES 6. DIMENSIONS ARE INCHES ONLY. DECIMALS ANGLES FLOW, THREADED, EXTRUSION A A X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV FINISH THIRD ANGLE PROJECTION SEE NOTES C 67131 30196 3 SCALE 2 : 1 SHEET 2 OF 2 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1