8 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REV. DESCRIPTION DATE APPROVED THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT THE PERMISSION OF VICOR CORP. 1 RELEASED PER ECO REQUEST E070416 REJH 03/05/07 EF 2 REVISED PER ECO REQUEST E091085 AR 07/14/09 REJH F F 3 REDRAWN PER E100871 DCS 6/11/10 KUK 4 REVISED PER E120702 ZMB 07/31/12 REJH <> 30 DRILL THRU SEE NOTE 6 <> ( .1285 ) .16 TYP (6) PL40 (12) PL010 SEE NOTE 5 MATL TO BE REMOVED E E 2.000 2.220 <> D D .190 .11 1.800 -A- <> 3.600 .100 <> .50 <> 4.60 .005 C C .410 B B NOTES: 1. MATERIAL: EXTRUSION SEE SHEET 2 OF 2. 2. REMOVE ALL BURRS AND SHARP EDGES. <> 3. CLEAR FINISH, RoHS COMPLIANT PER CST-0001, LATEST DRAWN BY DATE SWD REVISION PER A.) CHROMIUM FREE, OR B.) TRIVALENT CHROMIUM VICOR IN ACCORDANCE WITH MIL-DTL-5541, TYPE II, CLASS 1A OR 3. D.P. KELLY 10/05 SEE CST-0003 FOR TYPES OF AVAILABLE FINISHES. UNLESS OTHERWISE SPECIFIED 4.< DENOTES CRITICAL CHARACTERISTIC FOR LOT INSPECTION. DIMENSIONS ARE : INCH / MM HS CFG A LONG .4H LOW FLOW, 5. DIMENSIONS APPLIES AT SURFACE -A- (12) PL. TOLERANCES ARE: DECIMALS ANGLES A A THRU HOLE 6. MACHINED SURFACE TO BE .010 MAX BELOW SURFACE -A- (6) PL. X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 7. DIMENSIONS ARE INCHES ONLY. SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30718 4 1:1 2 SCALE SHEET OF 1 DO NOT SCALE DRAWING 8 7 6 5 4 3 2 18 7 6 5 4 3 2 1 VICOR CONFIDENTIAL REVISIONS THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS NOT TO BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART TO ANYONE WITHOUT REV DESCRIPTION DATE APPROVED THE PERMISSION OF VICOR CORP. SEE SHEET 1 F F E E R.035 (24) PL. SEE DETAIL A A 3.00 R.035 1.5 EACH SIDE OF VERT .410 .235 .200 .110 1.756 D D * .133 (9) PL. * .060 R.010 * .138 (8) PL. (2) PL. R.018 (2) PL023 (2) PL. * .058 .036 (2) PL. * .269 .031 .040 +.020 .017 2.220 .080 -.000 (2) PL. R.030 (8) PL252 C C * .030 * .060 PROFILE COMMON DETAIL A B B FOR SCALE 8 : 1 NOTES: 30195 1. MATL: ALUMINUM 6063-T5 30718 2. * DENOTES DIMENSION TO THEORETICAL SHARP CORNER. 32188 3. ALL DIMENSIONS ARE CRITICAL CHARACTERISTICS 30482 4. RoHS COMPLIANT PER CST-0001 LATEST REVISION. 5. DIMENSIONS ARE INCHES ONLY SWD DRAWN BY DATE VICOR A. RAGIPANI 07/14/09 UNLESS OTHERWISE SPECIFIED DIMENSIONS ARE : INCH / MM HS CFG LONG .4H LOW TOLERANCES ARE: DECIMALS ANGLES A A FLOW, THRU HOLE, EXTRUSION X.XX X.X = 0.01 0.25 1 X.XXX X.XX = 0.005 0.127 SIZE CAGE CODE DWG NO REV THIRD ANGLE PROJECTION C 67131 30718 4 SCALE 1:1 2 2 SHEET OF DO NOT SCALE DRAWING 8 7 6 5 4 3 2 1