715P15452LD3

Type 715P Vishay Sprague Polypropylene Film Capacitors ORANGE DROP , Low Loss Polyproplyene plastic film is employed as the dielectric in Type 715P ORANGE DROP capacitors. Type 715P capacitors are ideal for applications where high AC current flow is found, RoHS as in certain solid-state TV vertical circuits, r-f COMPLIANT generators and pulse-forming networks where dielectric heating is often a problem. The polyproplyene dielectric film is similar to polystyrene in that it can handle high AC currents due to is low loss but with the added advantage of an operating temperature to + 105 C. Capacitance change with temperature is less than 3 % over the entire operating temperature range. The temperature coefficient is negative and virtually linear at 180 PPM/C over the temperature range of + 25 C to + 105 C. This characteristic means the Type 715P is suitable for matching with positive TC resistors and inductors to maintain circuit stability. Type 715P ORANGE DROP capacitors are conformally coated with a flame retardant epoxy. Performance characteristics, as well as curves showing typical variation in electrical characteristics as a function of temperature and frequency, are given. PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 C to + 85 C, standard up to Humidity Test: Condition capacitors with no voltage applied + 105 C when working voltage is reduced to 50 % of the for 72 hours at 95 % relative humidity and + 75 C. Remove + 85 C rating. capacitors from humidity chamber, wipe surface dry of moisture and dry in circulating air for 4 hours. Measure Insulation Resistance: After a 2 minute charge at rated insulation resistance after a two minute charge at + 25 C voltage or 500 V, whichever is less. and rated voltage or 500 VDC, whichever is less. Minimum At + 25 C: 400 000 Megohm for C 0.5 F product of insulation resistance and capacitance shall be 200 000 Megohm - Microfarads for C > 0.5 Microfarads 50 000 Megohm - microfarads after test but need not exceed At + 85 C: 20 000 Megohm for C 0.5 Microfarads 100 000 Megohm. Not more than one failure in 12 units 10 000 Megohm - Microfarads for C > 0.5 Microfarads tested shall be permitted. At + 105 C: 2000 Megohm for C 0.5 F DC Life Test: Capacitors are capable of withstanding a 500 1000 Megohm - Microfarads for C > 0.5 Microfarads hour life test at + 85 C at 150 % of rated working voltage. Capacitance Tolerance and Dissipation Factor: After test, capacitance shall not have changed by more than Capacitors shall be measured at a frequency of 1000 Hz at 5 % of initial value, insulation resistance shall not have + 25 C or else be referred to measurements made at that decreased by more than 50 % of the initial limit and frequency and temperature. The maximum dissipation factor dissipation factor shall not have increased to more than shall be 0.1 %. 0.1 %. Dielectric Withstanding Voltage: AC Life Test: Capacitors shall withstand the maximum Capacitors rated below 1000 volts shall withstand a DC 60 Hz voltage for a period of 500 hours at + 85 C. potential of 250 % of rated voltage applied between terminals for not more than 5 seconds. Capacitance rated 1000 volts Rated DC Voltage Maximum 60 Hz Voltage and above shall withstand a DC potential of 200 % of rated 155 200 voltage applied between the terminals for not more than 5 200 400, 600 seconds. The test voltage must be applied and discharged 500 800, 1200, 1600 through a resistor of 1 ohm per volt. Not more than one failure allowed in 12 units tested. Document Number: 42018 For technical questions, contact: spresale vishay.com www.vishay.com Revision: 13-Feb-07 25.27F .039F .18F .47F .012F .039F .082F .47F .0039F .018F Type 715P Polypropylene Film Capacitors Vishay Sprague ORANGE DROP , Low Loss DIMENSIONS in inches (millimeters) L L L D Max. Max. Max. Max. 0.250 0.250 0.250 6.350 6.350 6.350 Max. Max. Max. 1.250 Lead Lead 31.750 Length Length Min. 0.032 0.813 Dia. (No. 20 AWG) Tinned Copper-Clad Steel S S S Terminal A Terminal B Terminal D S CASE L Terminal A Terminal B Terminal D CODE (Max.) 0.060 1.524 0.030 0.762 0.030 0.762 J 0.75 19.050 0.500 12.700 0.500 12.700 0.375 9.525 K 0.95 24.130 0.688 17.475 0.688 17.475 0.375 9.525 L 1.30 33.020 1.031 26.187 0.969 24.613 0.719 18.263 M 1.70 43.180 1.406 35.712 1.344 34.138 1.094 27.788 PERFORMANCE CHARACTERISTICS + 2 -2 10 + 1 0 5 - 1 TYPICAL 2 - 2 - 55 - 25 0 + 25 + 50 + 85 + 105 + 125 - 50 + 75 + 100 -3 10 TEMPERATURE DEG. CENTIGRADE 5 0.075 TYPICAL 2 0.05 TYPICAL 0.025 -4 10 1 2 5 10 2 5 100 2 5 1000 0 - 55 - 25 0 + 25 + 50 + 85 + 105 + 125 TEMPERATURE DEG. CENTIGRADE - 50 + 75 + 100 TEMPERATURE DEG. CENTIGRADE 1000 1000 5 5 2 200 155 100 100 5 5 2 2 400 V 200 V 10 10 1 2 5 10 2 5 100 2 5 1000 1 2 5 10 2 5 100 2 5 1000 FREQUENCY - kHz FREQUENCY - kHz www.vishay.com For technical questions, contact: spresale vishay.com Document Number: 42018 26 Revision: 13-Feb-07 PERCENT DISSIPATION PERCENT CAPACITANCE VOLTS - rms FACTOR - CHANGE - 1000 Hz 1000 Hz VOLTS - rms TAN