M39003/01 www.vishay.com Vishay Sprague Solid-Electrolyte TANTALEX Capacitors, Military MIL-PRF-39003/01 Qualified, Style CSR13 FEATURES Hermetically sealed Metal cased Axial lead Weibull failure rates G, B, C, D Exponential failure rates M, P, R, S Tape and reel available per EIA-296 standard PERFORMANCE CHARACTERISTICS STYLE, MILITARY SPECIFICATION SHEET Operating Temperature: -55 C to +125 C Style CSR13, M39003/01 MIL-PRF-39003/1 (above 85 C, voltage derating is required) Capacitance Range: 0.033 F to 330 F Capacitance Tolerance: 5 %, 10 %, 20 % Voltage Rating: 6 V to 100 V DC DC DESCRIPTION Solid-Electrolyte TANTALEX capacitors to military MIL-PRF-39003 establishes failure rates (expressed in specification MIL-PRF-39003 - Exponential and Weibull percent per 1000 h) based on exponential and Weibull Distribution: hermetically sealed, metal cased, axial leaded distribution. Care must be exercised in ordering to insure the tubular capacitors manufactured as military style CSR13. part number correctly identifies the desired failure rate level. These capacitors are furnished to the requirements of the In addition, each order for military style CSR13, CSR21, military specification, including marking, testing and CSR23 capacitors requiring government inspection must inspection. state whether inspection is to be at the destination or at the In accordance with the specification, all capacitors are Vishay Sprague plant. Orders requiring source inspection marked with the military part number (M39003/xx-xxxx) cannot be shipped until this has been accomplished. rather than the older style designation (CSRxxxxxxxx) and Style CS13 capacitors previously shown in MIL-C-26655 are should be ordered as such. All capacitors covered by directly replaced by style CSR13 and style CSR23 MIL-PRF-39003 are now ordered with the military part capacitors are extended capacitance range versions of number as illustrated in the Part Numbering System chart. military style CSR13. Capacitors must not be ordered using the style number For information on the performance characteristics of these identification. capacitors, please refer to the latest issue of the military specification. ORDERING INFORMATION M39003 /01 -2254 A /TR (1) BASIC SLASH SHEET DASH NUMBER SURGE CURRENT PACKAGING OPTION DOCUMENT NUMBER OPTION LETTER Indicates the Basic Indicates the Taken from Ratings Blank = standard Blank = bulk Specification in this Specification Sheet table of the (no surge current) /TR = tape and reel case MIL-PRF-39003 of the Basic Military Specification Sheet A = +25 C, /HR = tape and reel, half reel Specification after Weibull /PR = tape and reel, partial reel B = -55 C and +85 C, /RR = tape and reel, option R after Weibull /WR = tape and reel, option W C = -55 C and +85 C, before Weibull D = +25 C, after Weibull, high temperature solder E = -55 C and +85 C, after Weibull, high temperature solder F = -55 C and +85 C, before Weibull, high temperature solder H = high temperature solder only (no surge) Note (1) See detailed packaging information following the Standard Ratings table. Revision: 02-Jun-16 Document Number: 40018 1 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 M39003/01 www.vishay.com Vishay Sprague DIMENSIONS in inches millimeters D 1.500 0.250 J 38.10 6.35 M 0.094 2.4 L Max. D L M J CASE CODE + 0.016 0.41 0.031 0.79 0.002 0.05 (MAX.) - 0.015 0.38 A 0.286 7.26 0.135 3.43 0.020 0.51 0.422 10.72 B 0.474 12.04 0.185 4.70 0.020 0.51 0.610 15.49 C 0.686 17.42 0.289 7.34 0.025 0.64 0.822 20.88 D 0.786 19.96 0.351 8.92 0.025 0.64 0.922 23.42 Notes The case insulation shall extend 0.015 0.38 mm minimum beyond each end. However, when a shrink-fitted insulation is used, it shall lap over the ends of the capacitor body. A minimum lead length of 1.0 2.54 mm for use with tape and reel automatic insertion equipment is available upon request. RATINGS AND CASE CODES F 6 V 10 V 15 V 20 V 35 V 50 V 75 V 100 V 0.033 AA 0.039 AA 0.047 AA 0.056 AA 0.068 AA 0.082 AA 0.10 AAA 0.12 AAA 0.15 AAA 0.18 AAA 0.22 AAA 0.27 AAA 0.33 AAA 0.39 AAA 0.47 AAA 0.56 AAA 0.68 AA B 0.82 AB B 1.0 AB B 1.2 A B B B 1.5 A B B B 1.8 A B B B 2.2 A B B B 2.7 A B B B 3.3 A B B C 3.9 A B B C 4.7 A B C C 5.6 A B C C C 6.8 A B C C C Revision: 02-Jun-16 Document Number: 40018 2 For technical questions, contact: tantalum vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000