TSOP311.., TSOP313.., TSOP315.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise 1 Material categorization: 2 94 8691 for definitions of compliance please see 3 www.vishay.com/doc 99912 click logo to get started DESIGN SUPPORT TOOLS DESCRIPTION The TSOP311.., TSOP313.., and TSOP315.. series are miniaturized receivers for infrared remote control systems. A Models Available PIN diode and a preamplifier are assembled on a lead frame, the epoxy package contains an IR filter. The demodulated MECHANICAL DATA output signal can be directly connected to a microprocessor Pinning: for decoding. 1 = GND, 2 = V , 3 = OUT The TSOP313.. series devices are optimized to suppress S almost all spurious pulses from energy saving lamps like CFLs. AGC3 may also suppress some data signals if continuously transmitted. The TSOP311.. series are provided primarily for compatibility with old AGC1 designs. New designs should prefer the TSOP313.. series containing the newer AGC3. The TSOP315.. series contain a very robust AGC5. This series should only be used for critically noisy environments. These components have not been qualified according to automotive specifications. PARTS TABLE LEGACY, FOR SHORT BURST NOISY ENVIRONMENTS AND VERY NOISY ENVIRONMENTS AGC REMOTE CONTROLS (AGC1) SHORT BURSTS (AGC3) AND SHORT BURSTS (AGC5) 30 kHz TSOP31130 TSOP31330 TSOP31530 33 kHz TSOP31133 TSOP31333 TSOP31533 (1)(6) 36 kHz TSOP31136 TSOP31336 TSOP31536 Carrier frequency (2)(3)(4)(5) 38 kHz TSOP31138 TSOP31338 TSOP31538 40 kHz TSOP31140 TSOP31340 TSOP31540 56 kHz TSOP31156 TSOP31356 TSOP31556 Package Cast Pinning 1 = GND, 2 = V , 3 = OUT 1 = GND, 2 = V , 3 = OUT 1 = GND, 2 = V , 3 = OUT S S S Dimensions (mm) 10.0 W x 12.5 H x 5.8 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) Best remote control code MCIR Mitsubishi RECS-80 Code r-map XMP-1, XMP-2 RCMM Rev. 1.5, 24-Sep-2018 Document Number: 82493 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 TSOP311.., TSOP313.., TSOP315.. www.vishay.com Vishay Semiconductors BLOCK DIAGRAM APPLICATION CIRCUIT 16832 17170-11 R 1 2 Transmitter IR receiver V S with V 30 k + V S S TSALxxxx C 3 1 C OUT Band OUT Demo- Input AGC pass dulator V O GND GND 1 PIN Control circuit GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage (pin 2) V -0.3 to +6 V S Supply current (pin 2) I 3mA S Output voltage (pin 3) V -0.3 to (V + 0.3) V O S Output current (pin 3) I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current (pin 2) E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance d- 24 - m IR diode TSAL6200, I = 50 mA F 2 Output voltage low (pin 3) I = 0.5 mA, E = 0.7 mW/m , test signal see Fig. 1 V - - 100 mV OSL e OSL Pulse width tolerance: 2 Minimum irradiance E - 0.12 0.25 mW/m e min. t - 5/f < t < t + 6/f , test signal see Fig. 1 pi o po pi o 2 Maximum irradiance t - 5/f < t < t + 6/f , test signal see Fig. 1 E 30 - - W/m pi o po pi o e max. Directivity Angle of half transmission distance - 45 - 1/2 TYPICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb 0.40 Optical Test Signal E e (IR diode TSAL6200, I = 0.4 A, N = 6 pulses, f = f , t = 10 ms) F 0 0.35 0.30 t 0.25 Output pulse width t *) pi 0.20 T 0.15 *) t 6/f is recommended for optimal function pi 0 Input burst length Output Signal 0.10 14337 V O 1) 3/f < t < 9/f 0.05 0 d 0 = 950 nm, 2) t - 4/f < t < t + 6/f optical test signal, Fig. 1 V pi 0 po pi 0 OH 0 0.1 1 10 100 1000 10 000 100 000 V OL 1) 2) t t t d po 20771 E - Irradiance (mW/m) e Fig. 1 - Output Active Low Fig. 2 - Pulse Length and Sensitivity in Dark Ambient Rev. 1.5, 24-Sep-2018 Document Number: 82493 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 t - Output Pulse Width (ms) po Circuit