333 3 TSOP322.., TSOP324.., TSOP344.., TSOP348.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES Very low supply current Photo detector and preamplifier in one package Internal filter for PCM frequency Supply voltage: 2.5 V to 5.5 V Improved immunity against ambient light Insensitive to supply voltage ripple and noise Material categorization: 1 22 for definitions of compliance please see 33 16672 www.vishay.com/doc 99912 LINKS TO ADDITIONAL RESOURCES MECHANICAL DATA Pinning for TSOP348.., TSOP344..: Product Page 3D Models Calculators Marking Packages 1 = OUT, 2 = GND, 3 = V S Pinning for TSOP322.., TSOP324..: Holders Bends and Cuts 1 = OUT, 2 = V , 3 = GND S DESCRIPTION ORDERING CODE The TSOP322.., TSOP348.., TSOP324.. and TSOP344.. TSOP32.., TSOP34.. - 2160 pieces in tubes series are miniaturized IR receiver modules for infrared remote control systems. A PIN diode and a preamplifier are BLOCK DIAGRAM assembled on lead frame, the epoxy package contains an IR filter. V S The demodulated output signal can be directly connected to a microprocessor for decoding. 30 k The TSOP324.., TSOP344.. series devices are optimize d OUT to suppress almost all spurious pulses from energy saving Band Demo- Input AGC lamps like CFLs. The AGC4 used in the TSOP324.., pass dulator TSOP344.. may suppress some data signals. The TSOP322.., TSOP348.. series are provided primarily for GND compatibility with old AGC2 designs. New designs should PIN Control circuit prefer the TSOP324.., TSOP344.. series containing the newer AGC4. 16833-22 These components have not been qualified according to automotive specifications. APPLICATION CIRCUIT 17170-11 R 1 Transmitter IR receiver with V + V S S TSALxxxx C 1 C OUT V O GND GND R and C recommended to reduce supply ripple for V < 2.8 V 1 1 S Rev. 1.9, 14-Dec-2021 Document Number: 82489 1 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000 DDD D Circuit TSOP322.., TSOP324.., TSOP344.., TSOP348.. www.vishay.com Vishay Semiconductors PARTS TABLE LEGACY, FOR RECOMMENDED FOR AGC LONG BURST REMOTE CONTROLS (AGC2) LONG BURST CODES (AGC4) 30 kHz TSOP34830 TSOP32230 TSOP34430 TSOP32430 33 kHz TSOP34833 TSOP32233 TSOP34433 TSOP32433 (1)(2)(3) (1)(2)(3) 36 kHz TSOP34836 TSOP32236 TSOP34436 TSOP32436 Carrier frequency (4)(5) (4)(5) 38 kHz TSOP34838 TSOP32238 TSOP34438 TSOP32438 40 kHz TSOP34840 TSOP32240 TSOP34440 TSOP32440 (6)(7) (6)(7) 56 kHz TSOP34856 TSOP32256 TSOP34456 TSOP32456 Package Mold Pinning 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND 1 = OUT, 2 = GND, 3 = V 1 = OUT, 2 = V , 3 = GND S S S S Dimensions (mm) 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) (2) (3) (4) (5) (6) (7) Best choice for RC-5 RC-6 Panasonic NEC Sharp r-step Thomson RCA ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage V -0.3 to +6 V S Supply current I 3mA S Output voltage V -0.3 to (V + 0.3) V O S Output current I 5mA O Junction temperature T 100 C j Storage temperature range T -25 to +85 C stg Operating temperature range T -25 to +85 C amb Power consumption T 85 C P 10 mW amb tot Soldering temperature t 10 s, 1 mm from case T 260 C sd Note Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating onl y and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specificatio n is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (T = 25 C, unless otherwise specified) amb PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT E = 0, V = 3.3 V I 0.27 0.35 0.45 mA v S SD Supply current E = 40 klx, sunlight I -0.45- mA v SH Supply voltage V 2.5 - 5.5 V S E = 0, test signal see Fig. 1, v Transmission distance IR diode TSAL6200, d- 30 - m I = 50 mA F 2 I = 0.5 mA, E = 0.7 mW/m , OSL e Output voltage low V - - 100 mV OSL test signal see Fig. 1 Pulse width tolerance: 2 Minimum irradiance t - 5/f < t < t + 6/f , E - 0.08 0.15 mW/m pi 0 po pi 0 e min. test signal see Fig. 1 t - 5/f < t < t + 6/f , pi 0 po pi 0 2 Maximum irradiance E 30 - - W/m e max. test signal see Fig. 1 Directivity Angle of half transmission distance - 45 - 1/2 Rev. 1.9, 14-Dec-2021 Document Number: 82489 2 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc 91000