310406

IEC 309 PIN & SLEEVE DEVICES PERFORMANCE SPECIFICATIONS INTERNATIONAL RATINGS IEC 309 PIN & SLEEVE DEVICES PERFORMANCE SPECIFICATIONS INTERNATIONAL RATINGS ELECTRICAL TABLE 1 Insulation Resistance 500V for 1 min. Resistance 5M Connect and Disconnect Cycles Per IEC 309-1, Clause 19 Cycles with Device Load at Rated Dielectric Strength 3000V for 1 min. Rating Current and No-Load Per IEC 309-1, Clause 19 Amperes Voltage Cycles Sequence Norm. Operation, Connect See Table 1 16 5000 p.f of 0.6 0 - & Disconnect Cycles 32 1000 p.f of 0.6 1000 Alternating Per IEC 309-1, Clause 21 63 1000 p.f of 0.6 1000 Alternating Breaking Capacity Tested at 110 % of the rated operating 125 250 p.f of 0.7 250 Alternating Per IEC 309-1, Clause 20 voltage and 125% of the rated current. The test sequence is conducted by using a no-load, followed by a load Temperature Rise Maximum 50 K rise at full rated current. sequence. Per IEC 309-1, Clause 22 TABLE 2 Cable Secureness Test MECHANICAL Device Maximum Cable Secureness See Table 2 Rating Force Torque Displacement Per IEC 309, Clause 23 Amperes NNm mm Impact A device is wired with a 2.25m length 16 80 0.350 2 Per IEC 309, Clause 24 of flexible cord and dropped from a 32 100 0.425 2 height of 75 cm, 8 times. The device 63 120 0.8 2 is then tested for applicable degrees 125 200 1.5 2 of protection against moisture. The flexible cord or cable is twisted and pulled. Values for the applied twisting torque and force of pull are shown in Table 2. In all cases the cord displacement is less than 2mm. ENVIRONMENTAL Flammability Self-extinguishing Per IEC 309-1, Clause 27 Ambient Temperature Minimum: -25C with impact Range Maximum: 90C Moisture Resistance Watertight (IP67): Device immersed for 24 hours in water at a temp. of 25C, the highest point of the device being 5cm (2) below the water level. Splashproof (IP44): Device is sprayed with water for 10 minutes and immediately afterwards subjected to splashing water in all directions (360). UV Resistance Exposed plastic materials are UV stabilized. DECLARATION OF CONFORMITY WALTHER WERKE, Ferdinand Walther GmbH Ramsener Strasse 6 67304 Eisenberg We declare, under our sole responsibility, the conformity of the following products and standards: DIN EN ISO 9001 Certificate Registration No. 4678-01 Plugs and Sockets (Pin and Sleeve devices) DIN EN 60 309, T. 1/BS 4343 DIN EN 60 309, T. 2 This declaration of conformity is according to the EC regulations 73/23, 91/368 and 89/336 (Low Voltage Directive), module A, in consideration of DIN EN 45 014. 19 19 IEC 309 PIN & SLEEVE DEVICES INTERNATIONAL RATINGS IEC 309 PIN & SLEEVE DEVICES INTERNATIONAL RATINGS 16 AMPS 16 AMPS WATERTIGHT (IP67) SPLASHPROOF (IP44) MALE PLUGS with cable gland with cable sleeve Angled 90 Clock Position No. of of Ground Wires Voltage AC Contact 2P + G 110 4 219304 211304 210304 216304 230 6 219306 211306 210306 216306 3 400 9 219309 211309 210309 216309 3P + G 110 4 219404 211404 210404 216404 230 9 219409 211409 210409 216409 400 6 219406 211406 210406 216406 440 11 219411 211411 210411 216411 4 500 7 219407 211407 210407 216407 >50 (100-300Hz) 10 219410 211410 210410 216410 >50 (300-500Hz) 2 219402 211402 210402 216402 3P + N + G 110 4 219504 211504 210504 216504 230 9 219509 211509 210509 216509 5 400 6 219 211 210 216 440 11 219511 211511 210511 216511 7 6P + G 400 6 211706 210706 WATERTIGHT (IP67) SPLASHPROOF (IP44) FEMALE CONNECTORS (Couplers) with cable gland with cable sleeve Angled 90 Clock Position No. of of Ground Wires Voltage AC Contact 2P + G 110 4 319304 311304 310304 316304 230 6 319306 311306 310306 316306 3 400 9 319309 311309 310309 316309 3P + G 110 4 319404 311404 310404 230 9 319409 311409 310409 400 6 319406 311406 310406 440 11 319411 311411 310411 4 500 7 319407 311407 310407 >50 (100-300Hz) 10 319410 311410 310410 >50 (300-500Hz) 2 319402 311402 310402 3P + N + G 110 4 319504 311504 310504 230 9 319509 311509 310509 5 400 6 319 311 310 440 11 319511 311511 310511 6P + G 400 6 311706 310706 7 20 20