FKM2D011501A00JSSD WIMA

D WIMA FKM 2 Film and Foil Capacitors with Mixed Dielectric for Pulse Applications in PCM 5 mm Special Features Electrical Data Pulse duty construction Capacitance range: Capacitance change versus temperature Constant capacitance value 1000 pF to 0.022 mF (E12-values on request) (f = 1 kHz) (general guide) C/ C ( %) versus temperature (similar to Rated voltages: 4 the obsolete Polycarbonate) 100 VDC, 250 VDC, 400 VDC 3 2 Low dissipation factor Capacitance tolerances: 1 According to RoHS 2002/95/EC 20%, 10%, 5% (2.5% available 0 subject to special enquiry) -1 -2 Operating temperature range: Typical Applications -3 55+ C to +100+ C -4 -5 5 - 40 -2 0 0 20 40 60 80 100 Climatic test category: For general DC-applications T(C ) 55/100/56 in accordance with IEC Voltage derating: requiring a high capacitance Insulation resistance at +20+ C: A voltage derating factor of 1.35 % per K stability versus temperature e.g. 5 5 x 10 M must be applied from +85+ C for DC Automotive electronics 6 (mean value: 1 x 10 M) voltages and from +75+ C for AC Lighting Measuring voltage: 100 V/1 min. voltages Test voltage: 2 U , 2 sec. Reliability: r Construction Dissipation factors at +20+ C: tan d Operational life 300 000 hours Failure rate 5 fit (0.5 x U and 40+ C) r at f C 0.022 mF Dielectric: Mixed film -3 1 kHz 3 x 10 Capacitor electrodes: -3 10 kHz 5 x 10 Metal foil -3 100 kHz 8 x 10 Internal construction: Maximum pulse rise time: 1000 V/msec for pulses equal to the rated voltage Plastic film Metal foil electrode Mechanical Tests Packing Terminating wire Pull test on leads: Available taped and reeled. 10 N in direction of leads according to IEC 60068-2-21 Detailed taping information and graphs Vibration: at the end of the catalogue. 6 hours at 10 ... 2000 Hz and 0.75 mm Encapsulation: displacement amplitude or 10 g in Solvent-resistant, flame-retardant plastic accordance with IEC 60068-2-6 case with epoxy resin seal, UL 94 V-0 Low air density: Terminations: 1kPa = 10 mbar in accordance with Tinned wire. IEC 60068-2-13 Marking: Bump test: Colour: Red. Marking: Gold. 2 4000 bumps at 390 m/sec in For further details and graphs please Epoxy resin seal: Yellow. accordance with IEC 60068-2-29 refer to Technical Information. 35 01.10 D WIMA FKM 2 CCoonnttiinnuuaattiioonn GGeenneerraall DDaattaa 100 VDC/63 VAC* 250 VDC/160 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 1000 pF 2.5 6.5 7.2 5 FKM2D011001A00 2.5 6.5 7.2 5 FKM2F011001A00 1500 2.5 6.5 7.2 5 FKM2D011501A00 2.5 6.5 7.2 5 FKM2F011501A00 2200 2.5 6.5 7.2 5 FKM2D012201A00 2.5 6.5 7.2 5 FKM2F012201A00 3300 2.5 6.5 7.2 5 FKM2D013301A00 3.5 8.5 7.2 5 FKM2F013301C00 4700 3.5 8.5 7.2 5 FKM2D014701C00 3.5 8.5 7.2 5 FKM2F014701C00 6800 3.5 8.5 7.2 5 FKM2D016801C00 4.5 9.5 7.2 5 FKM2F016801E00 0.01 mF 4.5 9.5 7.2 5 FKM2D021001E00 5.5 11.5 7.2 5 FKM2F021001H00 0.015 5.5 11.5 7.2 5 FKM2D021501H00 7.2 13 7.2 5 FKM2F021501K00 0.022 7.2 13 7.2 5 FKM2D022201K00 400 VDC/200 VAC* Capacitance W H L PCM** Part number 1000 pF 2.5 6.5 7.2 5 FKSMG011001A00 1500 3.5 8.5 7.2 5 FKSMG011501C00 2200 3.5 8.5 7.2 5 FKSMG012201C00 3300 4.5 9.5 7.2 5 FKSMG013301E00 4700 4.5 9.5 7.2 5 FKSMG014701E00 6800 5.5 11.5 7.2 5 FKSMG016801H00 0.01 mF 7.2 13 7.2 5 FKSMG021001K00 * AC voltage: f 400 Hz 1.4 x U + UDC U rms r ** PCM = Printed circuit module = lead spacing Dims. in mm. Impedance change with frequency (general guide). W L H d = 0.5 l 6 -2 d Part number completion: 5 Tolerance: 20 % = M PCM at the lead exit points 10 % = K ( 0.5) 5 % = J 2.5 % = H Packing: bulk = S Lead length: 6-2 = SD Taped version see page 140. Rights reserved to amend design data without prior notification. 36 01.10