MKS0C031000C00JSSD WIMA

D WIMA MKS 02 Metallized Polyester (PET) Capacitors in PCM 2.5 mm Special Features Electrical Data High volume/capacitance ratio Capacitance range: Dissipation factors at + 20) C: tan d and reduced base 3300 pF to 1.0 mF (E12-values on request) at f C 0.1 mF 0.1 mF P C 1.0 mF PCM 2.5 mm Rated voltages: -3 -3 1 kHz 8 x 10 8 x 10 Self-healing 50 VDC, 63 VDC, 100 VDC, 250 VDC -3 -3 10 kHz 15 x 10 15 x 10 According to RoHS 2002/95/EC Capacitance tolerances: -3 100 kHz 30 x 10 20%, 10% (5% available subject to special enquiry) Voltage derating: Typical Applications Operating temperature range: A voltage derating factor of 1.25 % per K 55+ C to +100+ C must be applied from +85+ C for DC For general DC-applications e.g. Test specifications: voltages and from +75+ C for AC By-pass In accordance with IEC 60384-2 voltages. Blocking and EN 130 400 Reliability: Coupling and decoupling Climatic test category: Operational life 300 000 hours Timing 55/100/21 in accordance with IEC Failure rate P 2 fit (0.5 x U and 40) C) r Insulation resistance at +20+ C: Construction U U C 0.33 mF 0.33 mF < C 1.0 mF r test Dielectric: 3 3.75 x 10 M 1250 sec (M x mF) 50 VDC 10 V Polyethylene-terephthalate (PET) film 4 (mean value: 1 x 10 M) (mean value: 3000 sec) Capacitor electrodes: 3 3.75 x 10 M 1250 sec (M x mF) Vacuum-deposited 63 VDC 50 V 4 (mean value: 1 x 10 M) (mean value: 3000 sec) Internal construction: 4 1 x 10 M 100 VDC 100 V 4 (mean value: 2 x 10 M) Plastic film Measuring time: 1 min. Vacuum-deposited Test voltage: 1.6 U , 2 sec. electrode r Metal contact layer Maximum pulse rise time: (schoopage) Terminating wire Capacitance Pulse rise time V/msec pF/mF max. operation/test 3300 ... 6800 100 / 1000 0.01 ... 0.022 50 / 500 0.033 ... 0.068 30 / 300 Encapsulation: 0.1 ... 0.33 20 / 200 Solvent-resistant, flame-retardant plastic 0.47 ... 1.0 15 / 150 case with epoxy resin seal, UL 94 V-0 Terminations: for pulses equal to the rated voltage Tinned wire. Marking: Mechanical Tests Packing Colour: Red. Marking: Silver. Epoxy resin seal: Yellow Pull test on leads: Available taped and reeled. 10 N in direction of leads according to IEC 60068-2-21 Detailed taping information and graphs Vibration: at the end of the catalogue. 6 hours at 10 ... 2000 Hz and 0.75 mm displacement amplitude or 10 g in accordance with IEC 60068-2-6 Low air density: 1kPa = 10 mbar in accordance with IEC 60068-2-13 Bump test: 2 4000 bumps at 390 m/sec in For further details and graphs please accordance with IEC 60068-2-29 refer to Technical Information. 25 11.10 D WIMA MKS 02 Continuation General Data 50 VDC/30 VAC* 63 VDC/40 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 0.01 mF 2.5 7 4.6 2.5 MKS0C021000B00 0.015 2.5 7 4.6 2.5 MKS0C021500B00 0.022 2.5 7 4.6 2.5 MKS0C022200B00 0.033 2.5 7 4.6 2.5 MKS0C023300B00 0.047 2.5 7 4.6 2.5 MKS0C024700B00 0.068 3 7.5 4.6 2.5 MKS0C026800C00 0.1 mF 3 7.5 4.6 2.5 MKS0C031000C00 0.15 3 7.5 4.6 2.5 MKS0C031500C00 0.22 3 7.5 4.6 2.5 MKS0C032200C00 0.33 3.8 8.5 4.6 2.5 MKS0C033300D00 0.47 4.6 9 4.6 2.5 MKS0C034700E00 0.68 5.5 10 4.6 2.5 MKS0C036800F00 1.0 mF 5.5 10 4.6 2.5 MKS0B041000F00 100 VDC/63 VAC* 250 VDC/160 VAC* Capacitance W H L PCM** Part number W H L PCM** Part number 3300 pF 2.5 7 4.6 2.5 MKS0F013300B00 4700 2.5 7 4.6 2.5 MKS0F014700B00 6800 2.5 7 4.6 2.5 MKS0F016800B00 0.01 mF 2.5 7 4.6 2.5 MKS0D021000B00 2.5 7 4.6 2.5 MKS0F021000B00 0.015 2.5 7 4.6 2.5 MKS0D021500B00 2.5 7 4.6 2.5 MKS0F021500B00 0.022 2.5 7 4.6 2.5 MKS0D022200B00 2.5 7 4.6 2.5 MKS0F022200B00 0.033 2.5 7 4.6 2.5 MKS0D023300B00 3 7.5 4.6 2.5 MKS0F023300C00 0.047 2.5 7 4.6 2.5 MKS0D024700B00 3.8 8.5 4.6 2.5 MKS0F024700D00 0.068 3 7.5 4.6 2.5 MKS0D026800C00 4.6 9 4.6 2.5 MKS0F026800E00 0.1 mF 3 7.5 4.6 2.5 MKS0D031000C00 5.5 10 4.6 2.5 MKS0F031000F00 0.15 3.8 8.5 4.6 2.5 MKS0D031500D00 0.22 4.6 9 4.6 2.5 MKS0D032200E00 0.33 5.5 10 4.6 2.5 MKS0D033300F00 * AC voltage: f = 50 Hz 1.4 x U + UDC U rms r ** PCM = Printed circuit module = lead spacing Dims. in mm. W L Part number completion: H d = 0.4 l Tolerance: 20 % = M 10 % = K 6 -2 5 % = J d Packing: bulk = S 2.5 PCM Lead length: 6-2 = SD at the lead exit points ( 0.5) Taped version see page 127. Impedance change with frequency (general guide). Rights reserved to amend design data without prior notification. 26 11.10