C30

DC-HVDC Converter C Series 1 Watt +12VDC Input 11.5 to 16V xxx Series Voltage Regulated Output Voltages from 100V to 8000V 0 to 100% Programmable Output High Reliability 2.6MHrs MTBF <50ppm/C Temperature Coefficient Shielded Case for Low EMI Low Ripple - down to 0.002% 3 Year Warranty Dimensions: C01 - C20: 1.40 x 1.11x 0.50 (35.6 x 28.2 x 12.7mm) The C Series is a line of miniature, regulated high voltage power supplies. Each model is C25 - C40: 1.75 x 1.11 x 0.50 (44.4 x 28.2 x 12.7mm) programmed from 0 to 100% of rated output via a 0 to +5 volt, DAC-compatible, high-impedance C50 - C60: 2.10 x 1.11 x 0.50 (53.3 x 28.2 x 12.7mm) C80: 2.50 x 1.25 x 0.60 (63.50 x 31.75 x 15.24mm) programming input voltage. An externally accessible potentiometer provides adjustable gain trim, allowing for individual calibration of units. Key Applications: These converters exhibit very low ripple, noise, and EMI/RFI by utilizing a quasi-sinewave Photo Multiplier Tube oscillator, shielded transformer, excellent filtering techniques and an isolated steel enclosure Solid State Detectors featuring a separate grounding pin. A proprietary encapsulation process and a custom UL 94 V-0 Electrophoresis listed, high-performance formula are used to achieve excellent high voltage and thermal Piezo Devices properties. Temperature drift is typically less than 50ppm/C. Capacitor Charging EO Lenses Input Characteristic Minimum Typical Maximum Units Notes & Conditions Input Voltage Range 11.5 13.75 16 VDC Works with nominal 12V or 15V supply Input Current, Full Load 250 mA Input Current, No Load 100 mA Programming Inputs 0 5 VDC Analog DC Voltage Controls Output 0 to 100% Input Capacitance 440 A Low ESR Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 8000 VDC See Models and Ratings Table Output Current 10 mA See Models and Ratings Table Output Voltage programmable via Analog DC Programming Output Programming 0 100 % Voltage Input (4) Setpoint Accuracy 1 % Max Vpgm, No Load (5) Gain Adjust 5 % Potentiometer, See Signals & Controls (6) Linearity: Output vs Program 1 % 15 to 100% Output Minimum Load No minimum load required Start Up Response 250 msec At Max Vout, Full Load Line Regulation 0.05 1.0 % 100% Vpgm, Full Load, Min to Max Input Load Regulation 0.07 0.75 % 100% Vpgm, 13.75Vin, NL to FL Ripple and Noise 0.002 0.75 % 1MHz bandwidth, See Models and Ratings Table Temperature Coefficient 50 ppm/C Stability 100 ppm/hr After 30 minute warm up Notes 1. Maximum current is available at maximum output voltage. 5. GAIN ADJUST refers to the ability to alter the gain of the circuit to allow for 2. Specifications after 1 hour warm-up, full load, 25C, unless otherwise noted. set-point accuracy error. 3. Proper thermal management techniques are required to maintain safe case 6. LINEARITY refers to how much the transfer function can deviate from a straight temperature. line in the absence of any set-point error. 4. SET POINT ACCURACY refers to the ability of the unit to accurately deliver the programmed voltage. www.xppower.com 1DC-HVDC Converter C Series Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -10 +60 C Case Temperature Storage Temperature -20 +90 C Humidity 95 %RH Non-condensing Cooling Natural convection Thermal Shock Limit 1 C/10sec Natural convection Safety Approvals Safety Agency Safety Standard Notes & Conditions UL IEC/UL/CSA/EN 62368 CE CE Directive, RoHs and LVD Where applicable RoHS RoHS 2 and 3 Directive (2011/65/EU) Where applicable General Characteristic Minimum Typical Maximum Units Notes & Conditions Isolation: Input to Output N/A Input ground is connected to output ground Construction Case material is zinc plated steel. Solid vacuum encapsulation, UL 94 V-0 rated. Switching Frequency 50 350 kHz Mean Time Between Failure 2.6 MHrs Per Bellcore TR 332 Application Notes www.xppower.com 2