175 Watts xppower.com CLC Series High Efficiency Resonant Topology Medical Safety Approvals (-M Versions) 12 V Fan Output Remote Sense 5V Standby Option Remote On/Off & Power Good Signal Options 3 Year Warranty Specification Input General Input Voltage 85-264 VAC (120-370 VDC), derate output Efficiency 87% typical power 10% <90 VAC Isolation 3000 VAC Input to Output Input Frequency 47-63 Hz 4000 VAC Input to Output (-M) 2 x MOPP 1500 VAC Input to Ground 1 x MOPP Input Current 3.0 A typical at 115 VAC, full load 500 VAC Output to Ground 1.5 A typical at 230 VAC, full load Switching Frequency 70 kHz typical Inrush Current 40 A max at 230 VAC, cold start at 25 C Signals (Option -A) Power OK - open collector, Power Factor EN61000-3-2, class A Remote On/Off, 5 V Standby Earth Leakage Current 475 A 264 VAC at 60 Hz, 230 A MTBF 390 kHrs per MIL-HDBK-217F maximum at 264 VAC at 60 Hz (-M) at 25 C, GB Input Protection Internal T5 A 250 V fuse in line 3 Power Density 9.0 W/in Internal T5 A 250 V fuse in line and neutral (-M) Environmental Output Operating Temperature 0 C to +70 C derate linearly from +50 C Output Voltage 12-48 V (see tables) at 2.5%/C to 50% load at +70 C Output Voltage Trim 5% Cooling Forced-cooled >10 CFM Initial Set Accuracy 1% V1, 5% V2, 3% V3 Operating Humidity 95% RH, non-condensing Minimum Load 0.1 A required on V1 to maintain regulation Storage Temperature -40 C to +85 C of V2 Operating Altitude 3000 m Start Up Delay 1.5 s typical, see longform datasheet for Shock 30 g pk, half sine, 6 axes more details Vibration 2 g rms, 5 Hz to 500 Hz, 3 axes Start Up Rise Time 5 ms typical Hold Up Time 16 ms min at 115 VAC EMC & Safety Drift 0.2% after 20 min warm up Low Voltage PSU EMC EN61204-3, high severity level Line Regulation 0.5% max Emissions EN55011/32 level B conducted Load Regulation 1% V1, 5% V2 & V3 max EN55011/32 level A radiated Over/Undershoot 5% typical Harmonic Currents EN61000-3-2, class A Transient Response 4% max. deviation, recovery to within Voltage Flicker EN61000-3-3 1% in 500 s for a 50-75-50% load Radiated Immunity EN61000-4-3, level 3 Perf Criteria A change EFT/Burst EN61000-4-4, level 3 Perf Criteria A Ripple & Noise 1% pk-pk V1, others 2%, Surge EN61000-4-5, installation class 3 20 MHz bandwidth Perf Criteria A Overvoltage Protection 115-140% Vnom, recycle input to reset Conducted Immunity EN61000-4-6, level 3 Perf Criteria A Overload Protection 110-150% V1 only Dips & Interruptions EN61000-4-11, 30% 10 ms, 60% 100 ms, Short Circuit Protection Continuous trip and restart (hiccup mode) 100% 5000 ms Perf Criteria A, B, B Temperature 0.05%/C EN60601-1, 30% 500ms, 60% 100ms, Coefficient 100% 10ms, 100% 5000ms (-M) Remote Sense Compensates for 0.5 V total voltage drop Perf Criteria A, A (with 50% load), A, B Remote On/Off Uncommitted isolated optocoupler diode, Safety Approvals EN60601-1, ANSI/AAMI ES60601-1, (Inhibit/Enable) powered diode inhibits V1 & V2 CSA22.2 No.60601-1 per cUL, Including (Option -A) Risk Management, IEC60950-1:2005 Ed 2 / IEC62368-1:2014 UL 62368-1 & CAN/CSA C22.2 No. 62368- 1-14, EN62368-1:2014/A11:2017 AC-DCAC-DC CLC175 Models and Ratings Standby Supply Fan Output (1) (2,3) Output Power Output Voltage V1 Output Current V1 Model Number V2 V3 (optional) 175 W 12.0 VDC 13.90 A 12.0 V/0.5 A 5.0 V/0.5 A CLC175US12 175 W 24.0 VDC 6.90 A 12.0 V/0.5 A 5.0 V/0.5 A CLC175US24 (5) 175 W 28.0 VDC 6.25 A 12.0 V/0.5 A 5.0 V/0.5 A CLC175US28 175 W 48.0 VDC 3.50 A 12.0 V/0.5 A 5.0 V/0.5 A CLC175US48 Notes 1. 10 CFM airflow. 4. For cover with Top Fan assembly add -TF to model number e.g. CLC175US12-TF, 2. For medical version add, suffix -M to model number. CLC175US12-ATF, CLC175US12-MTF or CLC175US12-MATF. 3. For 5 V standby (V3), Power OK & Inhibit, add suffix -A to model number. 5. Not available for -A or -M. Mechanical Details 5.00 (127.0) 1.30 0.22 (5.7) 4.55 (115.6) (33.0) 0.20 (5.1) Inp ut Connector J1 Pin 1 Line Pin 2 Neutral 0.25Faston Earth 3.00 J1 mates with Molex housing (76.2) 2.50 09-50-1031 and Molex series (63.6) 2.55 1.90 5194 crimp terminals. (64.8) (48.3) 1.11 (28.3) 0.61 Output Connector J2 (15.6) Pin 1 +V1 Pin 2 +V1 0.23 (5.7) 0.19 (4.8) Pin 3 +V1 V Adj. SMD component height 0.20 (5.1) 0.14 0.25 Faston Pin 4 +V1 (3.5) Ground Tab 4 x 0.156 (3.96) Mounting Holes Pin 5 RTN 0.18 0.312 (7.92) Clearance Top & Bottom Pin 6 RTN (4.6) Pin 7 RTN 5.50 (139.7) Pin 8 RTN Fan Cover J2 mates with Molex housing 09-50-1081 and Molex series 5194 crimp terminals. Input Connector 3.50 Signal Connector J3 (88.9) Pin 1 +5V Standby Pin 2 Logic GND Pin 3 Logic GND 0.25 (0.6) Pin 4 Power OK Faston Ground Terminal Output Connector Pin 5 Inhibit HI Pin 6 Inhibit LO Pin 7 +Sense Pin 8 -Sense Pin 9 +Vout 2.00 Pin 10 -Vout (50.7) J3 mates with JST housing PHDR-10VS and JST SPHD- 001T-P0.5 crimp terminals. 4 x M3 x 0.5 THD 0.16 (4.0) Max Screw Penetration Fan Connector J4 Pin 1 Fan +(12V) 1.97 (50.0) Pin 2 Fan - J4 mates with Molex housing 22-01-1024 and Molex series 5103 crimp terminals. 0.77 (19.5) 0.39 (9.9) 4.724 (120.0) Notes 2 x M3 x 0.5 THD 1. All dimensions in inches (mm). 0.16 (4.0) Max Screw 0.98 (25.0) Tolerance .xx = 0.02 (0.50) Penetration .xxx = 0.01 (0.25) 2. Weight: 0.7 lbs (317 g) approx. 3. For thermal derating, please refer to longform datasheet. 0.39 (9.9) 4.72 (120.0) 18 Feb 20