IMM0212S3V3 XP Power

DC-DC Converter XPPower IMM02 Series 2 Watts World Wide Medical Approvals xxx Series Single and Dual Outputs SIP8 Package -20 C to +100 C Operation Full Load at 60 C Ambient 1500 VAC Isolation 1 x MOPP at 250VAC MTBF 1 MHrs 3 Year Warranty Dimensions: IMM02: 0.86 x 0.36 x 0.44 (21.85 x 9.2 x 11.1 mm) Models & Ratings Input current Maximum capacitive Input Voltage Output Voltage Output Current Model Number load No Load Full Load 3V3 606 mA 75 mA 694 mA 2200 F IMM0205S3V3 5 V 400 mA 75 mA 626 mA 2200 F IMM0205S05 12 V 167 mA 75 mA 617 mA 470 F IMM0205S12 15 V 133 mA 75 mA 617 mA 470 F IMM0205S15 4.5-9.0 V 3.3 V 303 mA 55 mA 684 mA 1000 F IMM0205D03 5 V 200 mA 55 mA 654 mA 1000 F IMM0205D05 12 V 83 mA 75 mA 601 mA 220 F IMM0205D12 15 V 66 mA 75 mA 601 mA 220 F IMM0205D15 3V3 606 mA 25 mA 317 mA 2200 F IMM0212S3V3 5 V 400 mA 25 mA 289 mA 2200 F IMM0212S05 12 V 167 mA 25 mA 285 mA 470 F IMM0212S12 15 V 133 mA 25 mA 289 mA 470 F IMM0212S15 9.0-18.0 V 3.3 V 303 mA 55 mA 317 mA 1000 F IMM0212D03 5 V 200 mA 55 mA 292 mA 1000 F IMM0212D05 12 V 83 mA 30 mA 285 mA 220 F IMM0212D12 15 V 66 mA 30 mA 281 mA 220 F IMM0212D15 Notes Input currents measured at low input voltage. Mechanical Details Pin Connections Pin Single Dual 1 -Vin -Vin 0.02 0.86 (21.85) 0.36 (9.20) (0.50) 2 +Vin +Vin Remote Remote Printed 3 On/Off On/Off Face Bottom View 0.36 0.01 0.42 0.44 (9.20) 0.12 6 +Vout +Vout (10.6) (0.25) (11.10) 0.13 (3.0) (3.20) 7 -Vout Common 8 No Pin -Vout 0.02 (0.50) 0.02 Notes (0.50) 1. All dimensions are in inches (mm) 0.10 2. Weight: 0.009 lbs (4.2 g) approx. (2.54) 3. Pin diameter: 0.020.002 (0.50.05) 0.70 (17.78) 4. Pin pitch tolerance: 0.014 (0.35) 5. Case tolerance: 0.02 (0.5) www.xppower.com 1DC-DC Converter XPPower IMM02 Series Input Characteristic Minimum Typical Maximum Units Notes & Conditions 4.5 9 VDC 5 V nominal Input Voltage Range 9 18 VDC 12 V nominal 2 Inrush Current 0.05 A s Input Reflected Ripple Current 30 mA pk-pk Through 12 H inductor and 47 F capacitor 16 VDC for 100 ms 5 V models Input Surge 25 VDC for 100 ms 12 V models Output Characteristic Minimum Typical Maximum Units Notes & Conditions Output Voltage 3.3 15 VDC See Models and Ratings table Initial Set Accuracy 2 % Minimum Load 0 % Line Regulation 0.5 % Load Regulation 2.0 % From 0% to full load On dual output models, when one output is at 25% load Cross Regulation 5 % and other is varied from 10% load to full load Ripple & Noise 1 % pk-pk 20 MHz bandwidth. Measured using 0.1 F ceramic capacitor Short Circuit Protection Continuous fold-back mode, with auto recovery Maximum Capacitive Load See Models and Ratings table Temperature Coefficient 0.03 %/ C Overload Protection 135 165 210 % Of nominal output current at nominal input voltage Output is on if remote on/off (pin 3) is open Remote On/Off Output turns off if 2-4 mA is applied to remote on/off (pin 3) General Characteristic Minimum Typical Maximum Units Notes & Conditions Efficiency 64 78 79 % Typical value is for IMM0212S12 Isolation: Input to Output 1500 VAC At 250 VAC working voltage, 1 x MOPP Switching Frequency 175 1000 kHz May enter burst mode frequency of 12-28 kHz at light load 9 Isolation Resistance 10 Isolation Capacitance 27 pF 3 Power Density 14 W/in Mean Time Between Failure 1 MHrs MIL-HDBK-217F, +25 C GB Weight 0.009 (4.2) lb (g) Environmental Characteristic Minimum Typical Maximum Units Notes & Conditions Operating Temperature -20 +100 C Derate from 100% load at +60 C to 50% at +80 C Storage Temperature -40 +125 C Case Temperature +105 C Humidity 95 %RH Non-condensing Cooling Natural convection www.xppower.com 2