xppower.com 150 Watts VFT Series 100 W Convection Rating 150 W Forced-cooled Rating 3x 5Package Single Outputs from 5 V to 48 V Built-in Fan Supply <0.5 W No Load Input Power Specification Input General Input Voltage 90-264 VAC Efficiency Up to 92%, see table Input Frequency 47-63 Hz Isolation 3000 VAC Input to Output 1500 VAC Input to Ground Input Current 2.5 A max at 115 VAC, 1.5 A max at 500 VDC Output to Ground 230 VAC Switching Frequency PFC: 45-80 kHz, PWM: 100-115 kHz Inrush Current 80 A max at 230 VAC, cold start 25 C MTBF >300 kHrs to MIL HDBK 217F at Earth Leakage Current 180 A max at 230 VAC/50 Hz 25 C, GB Power Factor >0.9 at 230 VAC and full load No Load Input Power <0.5 W Environmental Input Protection Internal T3.15 A/250 V fuse in line Operating Temperature -10 C to +70 C derate from 100% load at 50 C to 50% load at 70 C for 12, 24 & Output 48 V versions or 65 C for 5 & 15 V versions Cooling Convection-cooled: 100 W Output Voltage See table Forced-cooled: 150 W Output Voltage Trim None (120 W for 5 V models) with 15 CFM Initial Set Accuracy 2% at 50 % load Operating Humidity 5% to 90% RH, non condensing Minimum Load No minimum load requirement Operating Altitude 3000 m Start Up Delay 2 s max Storage Temperature -20 C to +85 C Start Up Rise Time 35 ms typical Shock IEC68-2-6, 30 g, 11 mins half sine, 3 times Hold Up Time 8 ms minimum at full load and 115 VAC in each of 6 axes Line Regulation 0.5% max Vibration IEC68-2-27, 10-55 Hz, 2 g 10 mins / Load Regulation 0.5% max sweep. 60 mins for each of 3 axes Transient Response 5% maximum deviation, recovering to less than 1% within 500 s for 50% step load EMC & Safety Ripple & Noise 5 V version: 85 mV pk-pk max, Emissions EN55032, level B conducted & radiated 1% pk-pk max for others (see note 1) Harmonic Currents EN61000-3-2 class A Overvoltage Protection 110-135%, recycle input to reset EN61000-3-2 class C for loads 60 W Overload Protection 130-160% Voltage Flicker EN61000-3-3 Short Circuit Protection Trip and restart (hiccup mode) ESD Immunity EN61000-4-2, 8 kV air, 4 kV contact, Temperature 0.02 %/C Perf Criteria A Coefficient Radiated Immunity EN61000-4-3, 3 V/m, Perf Criteria A Remote Sense Compensates for 0.5 V total voltage drop EFT/Burst EN61000-4-4, level 3, Perf Criteria A Fan Supply 5 V version: 5 V at 200 mA Surge EN61000-4-5, installation class 3, Other versions: 12 V at 300 mA Perf Criteria A Conducted Immunity EN61000-4-6, 3 V, Perf Criteria A Dips & Interruptions EN61000-4-11, 30% 10 ms, 60%, 100 ms, 100%, 5000 ms Perf Criteria A, B, B Safety Approvals UL60950-1, IEC60950-1, EN60950-1, UL62368-1, EN62368-1, IEC62368-1, CE (Meets all applicable directives), UKCA (Meets all applicable legislation) AC-DCAC-DC VFT150 Models and Ratings Output Current (2) Output Voltage Efficiency Model Number Convection-cooled Forced-cooled 5.0 V 16.0 A 24.00 A 83% VFT150PS05 (3) 12.0 V 8.30 A 12.50 A 87% VFT150PS12 15.0 V 6.66 A 10.00 A 87% VFT150PS15 24.0 V 4.20 A 6.25 A 92% VFT150PS24 48.0 V 2.10 A 3.13 A 92% VFT150PS48 Notes 1. Measured at the output connector with a 0.1 F ceramic capacitor and a 10 F 3. VFT150PS12 model is available with optional blocking diode, add suffix -D, electrolytic capacitor and 20 MHz bandwidth. e.g. VFT150PS12-D. 2. Average of efficiencies measured at 25%, 50%, 75% & 100% load and 230 VAC input. Mechanical Details 5.00 (127.0) 4.77 (121.3) 0.22 (5.7) 0.15 ( 4.0 x 4) 1 Fan 0.22 Connector (5.7) 1 Fan Connector 11 2.77 5 V +VO +VO (70.5) 1 Fan Connector 3.00 (76.2) -VO -VO L 0 V 1 N Sense 1 11Sense Sense Connector Connector Connector PS12/15 PS24/48 PS05 Mounting holes marked with 1.24 must be connected to safety earth (31.5) 1.10 (28.0) 0.06 0.10 (1.6) (2.5) Input Connector Output Connector (PS12-48) Sense Connector Fan Connector 1 +Vout Pin 1 Neutral Pin 1 Sense+ Pin 1 Fan+ 2 +Vout Pin 2 Sense- Pin 2 Fan- Pin 2 Live 3 +Vout 4 +Vout Mates with: JST PHR-2 Mates with: JST XHP-2 Mates with: JST Housing VHR-3N and 5 -Vout Housing and SPH-002T-PO.5S crimps. Housing and SXH-002T-PO.6 crimps JST Series SVH crimp terminals. 6 -Vout 7 -Vout 8 -Vout Notes Mates with: JST Housing VHR-8N and 1. All dimensions shown in inches (mm). 3. Tolerance: x.xx = 0.04 (x.x = 0.1) JST Series SNH crimp terminals 2. Weight: 0.75 lbs (340 g) approx x.xxx = 0.2 (x.xx = 0.5) Derating Curve 100 80 60 40 20 0 -10 0 10 20 30 40 50 60 70 80 Ambient Temperature (C) 28 Oct 2021 Output Power (%)