TIME RELAY PCM-02/U INSTRUCTION MANUAL Zakad Mechaniki i Elektroniki ZAMEL sp.j. J.W. Dzida, K. odziska ul. Zielona 27, 43-200 Pszczyna, Poland Tel. +48 (32) 210 46 65, Fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl DESCRIPTION TECHNICAL PARAMETERS PCM-02/U The one mode time relay PCM-02/U Input (supply) terminals: A1, A2 has a delayed switch off function (aver- Input rated voltage: 12 240 V AC/DC sive) in automation and control systems. The relay is released by power supply Input voltage tolerance: -5%, +10 % voltage. It has a wide time adjustment Supply voltage control indicator: LED green range from 0,1 s to 10 days. Additio- Nominal frequency: 50 / 60 Hz nal ON/OFF functions enable constant Rated power consumption: 15 mA switch on, switch off of the output (load). Operating mode number: 1 (switch off delay) The system has the indicators of power supply voltage, relay mode, and time me- Time adjustment range t: from 0,1 s to 10 days asure with the help of red LED diode.. Time measure accuracy: 0,2 % Time adjustment: 2x potentiometer (rotary + step) Power/relay supply indicator and time measure: LED red Output relay parameters: 1NO/NC - 16 A / 250 V AC1 4000 VA FEATURES Number of terminal clamps: 5 2 Section of connecting cables: from 0,2 to 2,50 mm Operating mode: switch off delay (in- o Ambient temperature range: from -20 to +60 C put voltage release), Operating position: free supply voltage control indicator - LED Mounting: green, TH 35 rail (PN-EN 60715) power/relay supply indicator and time Protection degree: IP20 (PN-EN 60529) measure - LED red, Protection class: II time measure accuracy, Overvoltage category: II wide time adjustment range, Pollution degree: 2 constant switch on, switch off func- tion, Rated impulse withstand voltage: 2 kV (PN-EN 61000-4-5) relay output - 1 change-over contact Dimensions (height / width / depth): monomodular (17,5 mm) 90x17,5x66 mm (NO/NC) contact max 16 A capacity, Weight: 0,09 kg TH 35 DIN rail installation. Reference standards: PN-EN 60730-1 PN-EN 60730-2-7 PN-EN 61000-4-2,3,4,5,6,11 The device is designed for one-phase installation and APPEARANCE must be installed in accor- dance with standards valid in a particular country. The Input supply terminal (A1) Input supply terminal (A2) device should be connec- CAUTION ted according to the details included in this operating manual. Installa- tion, connection and control should be car- ried out by a qualified electrician staff, who act in accordance with the service manual and the device functions. Disassembling of Supply voltage control indicator Power/relay supply indicator the device is equal with a loss of guarantee and can cause electric shock. Before in- stallation make sure the connection cables are not under voltage. The cruciform head screwdriver 3,5 mm should be used to in- Smooth time adjustment stal the device. Improper transport, storage, and use of the device influence its wrong functioning. It is not advisable to instal the device in the following cases: if any device part is missing or the device is damaged or Time adjustment choice deformed. In case of improper functioning of the device contact the producer. The symbol stands for selective collection of electrical and electronic devices. Placing used devices with other Output (load) relay terminals waste is not allowed VER. 001 10.07.2009MOUNTING FUNCTIONING 1. Disconnect the power supply from the ma- ins by the phase fuse, the circuit breaker or SWITCH OFF DELAY - after the supply voltage U has been the switch disconnector that are joined to the applied, the output relay R switches on immediately (pos.11- U 14), and the preset time t is measured. After the preset time proper circuit, t t t has been measured, the output relay R returns to the initial 2. Check if there is no voltage on connec- state (pos.11-12). tion cables by means of a special measu- re equipment, Diodes function Time adjustment example t 3. Install PCM-02/U device in the switchboard U description on TH 35 DIN rail, 1h 10min 5 6 10h 4. Connect the cables with the terminals accor- elay switched off 1min 4 7 t = TIMExRANGE, 10s 1d 3 8 (closed contacts 11-12), ding to installing diagram, 1s ON 2 9 time measure off t = 8 x 1 d = 8 d 1 10 0,1s OFF 5. Switch on the power supply from the mains, 6. Adjust the time using the TIME and RANGE relay switched on 1h 5 6 10min knobs, where t=TIMExRANGE. 10h 4 7 t = TIMExRANGE, 1min (closed contacts 11-14), 1d 10s 3 8 Switching on the power supply voltage cau- time measure on 2 9 1s ON t = 3 x 1 h = 3 h 1 10 0,1s OFF (flashing diode) ses the green LED luminosity. The cycle wil be automatically initiated with the adjusted t time. CONNECTING EXAMPLE OF INSTALLATION L(+) 12 240 V AC/DC N(-) TWILIGHT/SUNRISE DETECTION ROLLER BLINDS MOTORS START ROLLER BLINDS CENTRAL CLOSE IMPULSE ROLLER BLINDS CENTRAL OPEN IMPULSE LOCAL CONTROLL PCM-02/U time relay cooperates with the WZM-01 twilight switch and with SRM-10 roller blinds con- troller. Its function is impulse generation at dusk. This impulse is a signal for the roller blinds controllers (central closing input) and for moving down all the roller blinds working in the same group. PRODUCT FAMILY PCM-02/U time relay belongs to PCx time relay product family. DIMENSIONS INNER DIAGRAM Voltage type: 24V - 24 V AC/DC U - 12240 V AC/DC: available for PCM-01, PCM-02, PCM-03, PCM-06 U - 24250 V AC 30300 V DC: available for PCM-07 Device type: 01 - 1 operating mode switch on delay 02 - 1 operating mode switch off delay 03 - 1 operating mode cyclic change over 04 - 8 (PCP-04) or 10 (PCM-04) operating modes 06 - 2 operating modes - switch on/ switch off delay 07 - 25 operating modes, digital, two ranges of time operation 10 - 10 operating modes, two ranges of time RELAY CAPACITY operation Casing type: M - modular version (TH 35 DIN rail) P - flush junction box 60 version Device symbol GUARANTEE CARD There is 24 months guarantee on the product 1. ZMIE ZAMEL SP. J. assures 24 months guarantee for the product. 2. The manufacturers guarantee does not cover any of the following actions: a) mechanical damage during transport, loading / unloading or under other circumstances, b) damage caused by incorrect product mounting or misuse, c) damage caused by unauthorised modifications made by the PURCHASER or any third parties to the product or any other devices needed for the product functioning, d) damage caused by Act of God or any other incidents independent of the manufacturer. 3. The PURCHASER shall lay any claims in writing to the dealer or ZMIE ZAMEL SP. J. 4. ZMIE ZAMEL SP. J. is liable for processing any claim according to current Polish legislation. 5. ZMIE ZAMEL SP. J. shall process the claim at its own discretion: product repair, replacement or money return. 6. The manufacturers guarantee is valid in the Republic of Poland. 7. The PURCHASERs statutory rights in any applicable legislation whether against the retailer arising from the purchase contract or otherwise are not affected by this warranty. Salesman stamp and signature, date of sale VER. 001 10.07.2009 E E M M I I T T E E G G N N A A R R