RADIO ROLLER BLINDS CONTROLLER SRP-02 CONNECTION MOUNTING MANUAL INSTRUCTION 1. Disconnect power supply by the phase LOCAL LOCAL fuse, the circuit-breaker or the switch- disconnector combined to the proper circuit. ZAMEL Sp. z o.o. 2. Check if there is no voltage on con- nection cables by means of a special measure equipment. ul. Zielona 27, 43-200 Pszczyna, Poland 3. Connect the cables with the terminals in tel. +48 (32) 210 46 65, fax +48 (32) 210 80 04 www.zamelcet.com, e-mail: marketing zamel.pl accordance with the installing diagram. 4. Install SRP-02 device in the junction box. DESCRIPTION TECHNICAL DATA 5. Switch on the power supply from the Radio roller blinds controller SRP-02 is SRP-02 mains. used to control roller blind drives with 230V Input (supply) terminals: L, N AC motor with a limit switch. The device re- Input rated voltage: 230V AC alises roller blinds local and central control APPLICATION Input voltage tolerance: -15 +10 % functions and it has the possibility of comfort mode adjustment. Comfort modes are used Nominal frequency: 50 / 60 Hz to adjust roller blinds position (height level) Nominal power consumption: 0,4 W (stand-by mode) / 0,7 W (roller blind movement) and to memorise the height level. Central Transmission: radio 868,32 MHz Roller blinds control mode is used in case of a totally closed or system realised by means Coding way: unidirectional opened roller blind or a group of roller blinds of SRP-02 roller blinds Coding: addressing transmission with different position level. controllers. One controller Maximum number of transmitters: 32 can be used for one roller blind. Each of the Range: up to 250 m in the open area controllers is operated Maximum time of roller blind movement: 120 sec by means of a wireless Comfort mode time adjustment: 1 120 sec (every 0,1 sec) P-256/8 remote control. Optic signalling of transmitters operation: LED red diode The remote control can also control operation of Local control terminals: LOCAL (up), (down) FEATURES RDP-01 radio dimmer Roller blind motor power supply terminals: (up), (down) (switch on /switch off used in wired and wireless control of roller Relay contact parameters: 2NO 5 A / 250 V~ AC1 1250 VA (voltage contacts) control and light sources blind, sunblind and gate drives, (electric brightening / dimming) Number of terminal clamps: 6 motors of 230 V AC), and of RWL-01 radio 2 Section of connecting cables: 0,2 2,50 mm lighting switch. wired local control inputs, o Ambient temperature range: -10 +55 C easily installed in 60 mm junction box, Operating position: free energy-saving device, possibility of con- Casing mounting: installation cable box 60 mm stant work, Casing protection degree: IP20 (EN 60529) two comfort modes - upper and bottom Protection level: II - memory of roller blind height level (e.g. Overvoltage category: II roller blind open at a half height level), Pollution degree: 2 possibility of cooperation with any roller blind switch (which is not equipped in Surge voltage: 1 kV (EN 61000-4-5) backlight elements), Dimensions: 47,5 x 47,5 x 20 mm Weight: 0,039 kg Reference standard: EN 60669, EN 60950, EN 61000 The device is designed for APPEARANCE single-phase installation and must be installed in accord- ance with standards valid in a particular country. The device Local wired control terminals should be connected accord- (upward movement , downward movement ) CAUTION ing to the details included in The ZAMEL company devices this operating manual. Installation, connection Roller blind motor terminals which are characterised and control should be carried out by a qualified (upward movement , downward movement ) with this sign can cooperate electrician staff, who act in accordance with the service manual and the device functions. with each other. Input (supply) terminals (L, N) In case of casing dismantling an electric shock may occur, and the guarantee is lost then. Be- fore installation make sure the connection ca- bles are not under voltage. The cruciform head WARRANTY CARD screwdriver 3,5 mm should be used to instal the device. Improper transport, storage, and use of Optic signalling of receivers operation the device influence its wrong functioning. It There is 24 months guarantee on the product is not advisable to instal the device in the fol- 1. ZAMEL provides a two-year warranty for its products. Programming push-button lowing cases: if any device part is missing or 2. The ZAMEL warranty does not cover: a) mechanical defects resulting from transport, loading / unloading or other circumstances the device is damaged or deformed. In case of b) defects resulting from incorrect installation or operation of ZAMEL products c) defects resulting from any changes made by CUS- TOMERS or third parties, to products sold or equipment necessary for the correct operation of products sold d) defects resulting improper functioning of the device contact the from force majeure or other aleatory events for which ZAMEL is not liable e) power supply (batteries) to be equipped with a device producer. in the moment of sale (if they appear) 3. All complaints in relation to the warranty must be provided by the CUSTOMER in writing to the retailer after discovering a defect. The symbol means selective 4. ZAMEL will review complaints in accordance with existing regulations. collecting of electrical and electronic 5. The way a complaint is settled, e.g. replacement of the product, repair or refund, is left to the discretion of ZAMEL. 6. Guarantee does not exclude, does not limit, nor does it suspend the rights of the PURCHASER resulting from the discrepancy equipment. between the goods and the contract. It is forbidden to put the used equipment together with other waste Salesman stamp and signature, date of sale VER. 002 11.07.2011OPERATION RADIO TRANSMITTERS DELETION Pressing shortly the programmed push-button in local mode (<2 sec.) or roller blind switch (optional) causes the roller blind moves. Another short pressing of the same push-button or the switch causes the roller blind stops at a required level. Pressing the push-button or the switch longer (>2 sec.) causes comfort mode activates (the roller blind moves in a required direction and stops according to the adjusted time). Pressing shortly transmitters push-button (programmed in the central mode) causes complete opening or closing of the roller blind. Press PROG push-button of After 5 seconds LED red diode switches on Release the push-button in SRP-02 RADIO TRANSMITTERS PROGRAMMING SRP-02 device for a longer time. (signal pulsates) and then it switches off. - MEMORY IS DELETED. LOCAL mode: COOPERATION AND OPERATING RANGE Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01 RNK-02 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m RNK-04 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m Press PROG push-button of SRP-02 device for Press and release transmitters first Press and release the second P-256/8 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m a longer time until LED red diode switches on push-button (movement ). LED red transmitters push-button (movement ). (constant signal). Next release PROG push-button. diode switches on (first signal pulsates, LED red diode switches on (signal P-257/4 (2) 180 m 200 m 200 m 200 m 200 m 250 m 180 m 250 m 250 m 180 m 250 m next the signal is constant). pulsates) and then switches off - THE RNM-10 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m TRANSMITTER IS ADDED. RNP-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m CENTRAL mode: RNP-02 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RNL-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTN-01 200 m 200 m 200 m 200 m 200 m 250 m 200 m 250 m 250 m 200 m 250 m RCR-01 160 m 180 m 180 m lack* lack* 200 m 160 m 200 m 200 m 160 m 200 m RTI-01 160 m 180 m 180 m 180 m 180 m 200 m 160 m 200 m 200 m 160 m 200 m RXM-01 230 m 250 m 250 m 250 m 250 m 300 m 200 m 300 m 300 m 230 m 300 m Press PROG push-button of SRP-02 device for Press and release transmitters first Press and release the second transmitters a longer time until LED red diode switches on push-button (movement ). LED red push-button (movement ). LED red diode (constant signal). Next release PROG push-button. diode switches on (first signal pulsates, switches on (the signal pulsates) * 1-channel transmitters do not cooperate with roller blind controllers. Wait (for about 5 seconds) till LED red diode next the signal is constant). and next it switches off - THE CAUTION: The given range concerns open area - an ideal condition without any natural or artificial obstacles. If there are some obstacles between switches on (first signal pulsates, TRANSMITTER IS ADDED. a transmitter and a receiver, it is advisable to decrease the range according to: wood and plaster: from 5 to 20 %, bricks: from 10 to 40 %, next the signal is constant). reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 %, Over- and underground medium and high electrical power lines, radio and television transmitters, GSM transmitters set close to a device system have also a negative influence on the range. An exemplary programming procedure with P-257/4 remote control. The procedure for the rest of radio EXTA FREE transmitters is analogous with reservation that 2-channel transmitters can be programmed only in one mode - local or central. CAUTION: If push-button changes are required for local and central control (in a 4-channel transmitter) the programming procedu- RANGE LOSS CONCERNING RADIO SIGNALS GOING THROUGH OBSTACLES re should be for two modes separately (first local control push-buttons, then central control push-buttons). In case of a 2- channel transmitter the change from local control to central control should start with controllers memory deletion and only then transmitte- rs programming procedure for central mode can start. One transmitter can be added during one programming cycle. Full memory is signalled with pulsating LED red diode. bricks: from 10 to 40 %, wood and plaster: from 5 to 20 %, reinforced concrete: from 40 to 80 %, metal: from 90 to 100%, glass: from 10 to 20 % COMFORT MODE TIME PROGRAMMING TRANSMITTERS RECEIVERS RNK-02 RNL-01 ROP-01 RWL-01 2channel button Radio 1-channel Radio lighting radio transmitter foot transmitter radio receiver switch RNK-04 RTI-01 ROP-02 RWG-01 Open the roller blind Press PROG push-button of SRP-02 device for a longer time until Wait again (for about 5 seconds) till 4-channel button IR/EXTA FREE 2-channel Remote control completely. LED red diode switches on (constant signal). Next release PROG LED red diode switches on (first signal radio transmitter transceiver radio receiver socket push-button. Wait (for about 5 seconds) till LED red diode switches pulsates, next the signal is constant). on (first signal pulsates, next the signal is constant). P-256/8 RNM-10 RDP-01 SRP-02 8-channel 4-channel radio 1-channel Radio roller blinds remote control modular transmitter radio dimmer controller P-257/4 RNP-01 ROB-01/12-24V SRP-03 4-channel 4-channel Radio Central radio roller remote control radio transmitter gate controller blinds controller P-257/2 RNP-02 ROM-01 ROM-10 2-channel 4-channel 1-channel radio 2-channel remote control radio transmitter modular receiver radio modular receiver * urzdzenie przewodowe EXTA RCR-01 RXM-01 If the roller blind is in a required comfort position - Press PROG push-button of SRP-02 device, Radio RS-485/EXTA FREE press PROG push-button and release it next release PROG push-button - the roller motion sensor Transceiver - the roller blind stops blind moves automatically. ACCESSORIES - ROLLER BLIND MOVEMENT TIME IS ADDED. ANT-01 RTN-01 External antenna Retransmitter Time programming example for upper comfort mode. In order to programme time for bottom comfort mode, it is necessary to close the roller blind completely before programming procedure starts. Maximum time is 120 seconds.