Features: PSC-151 Series Universal AC input (88-264V AC) Installed on DIN rail TS-35 / 7.5 or 15 Built-in active PFC function, PF > 0.95 150% peak load capability E205412 100% full load burn-in test Protection: SCP, OLP, OVP, OTP Two selectable peak load modes Built-in DC OK Relay contact Built-in Remote ON / OFF function 3 years warranty UL 508 Cat. No. PSC-15124 PSC-15148 OUTPUT DC VOLTAGE 24V 48V RATED CURRENT 6.3A 3.2A CURRENT RANGE 0~6.3A 0~3.2A RATED POWER 150W 150W PEAK CURRENT 9.45A 4.8A PEAK POWER 225W (3sec.) 3 seconds or 20% duty cycle max. and the average output power should not exceed the rate power. RIPPLE & NOISE (max) 240mVp-p 480mVp-p Ripple & noise are measured at 20MHz of bandwidth by using a 12 twisted pair-wire terminated with a 0.1F & 47F parallel capacitor. VOLTAGE ADJ. RANGE -2% ~ +8% -2% ~ +8% VOLTAGE TOLERANCE 1.0% 1.0% Tolerance: includes set up tolerance, line regulation and load regulation. LINE REGULATION 0.5% 0.5% LOAD REGULATION 1.0% 1.0% SETUP, RISE TIME 700ms, 30ms / 230VAC / 115VAC at full load INPUT HOLD UP TIME (Typ.) 16ms / 230VAC 16ms / 115VAC at full load VOLTAGE RANGE 88 ~ 264VAC 124 ~ 373VDC Derating may apply in low input voltage. Please check the derating curve for more details. FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR(Typ.) 0.9 / 230VAC 0.98 / 115VAC at full load EFFICIENCY (Typ.) 87% 87% AC CURRENT (Typ.) 2.0A / 115VAC 1.0A / 230VAC INRUSH CURRENT (Typ.) 33A / 115VAC 65A / 230VAC LEAKAGE CURRENT <1mA/ 240VAC PROTECTION OVERLOAD PROTECTION 105% ~ 150% rated output power for 3 sec and then shutdown in O/P with auto-recovery. 150% or greater rated power or short circuit is constant current limiting. If O/P drops to 40% output then it auto-recover 5 times if fault condition is not removed during auto recovery, the system will shut down and needs to be restarted to recover. OVER VOLTAGE 29 ~ 33V 56 ~ 65V Protection type: Latch-off mode, repower on to recover. OVER TEMPERATURE 95 5C (TSW: detect on heatsink of power diode) Protection type: Shut down o/p voltage, recovers automatically after temperature goes down ENVIRONMENT WORKING TEMP. -10 ~ +70C (Refer to derating curve) Installation clearance: 40mm from top, 20mm from bottom, 5mm from the left and right side are recommended when loaded permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended. WORKING HUMIDITY 20 ~ 95% RH non-condensing STORAGE TEMP. / HUMIDITY -40 ~ +85C, 10 ~ 95% RH TEMP. COEFFICIENT 0.03% / C (0 ~ 50C) VIBRATION 10 ~ 500Hz, 2G 10min. / 1cycle, 60min. each along X, Y, Z axes SAFETY & EMC SAFETY STANDARDS UL 508 / TUV EN 60950-1 WITHSTAND VOLTAGE I/P-O/P: 4242VDC, I/P-FG: 2121VDC, O/P-FG: 707VDC, O/P-DC OK: 707VDC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG: >100M Ohms / 500VDC / 25C / 70% RH EMI CONDUCTION & RADIATION EN55022 (CISPR22) Class B HARMONIC CURRENT EN61000-3-2, -3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11 ENV50204 EN55024 EN61000-6-2 (EN50082-2) EN61204-3 heavy industry level criteria A, MEET SEMI F47 The power supply is considered a component which will installed into a final equipment. The final equipment must be OUTPUT re-confirmed that it still meets EMC directives. DC OK RELAY. CONTACT RATINGS (max) 60VDC / 0.3A, 30VDC / 1A, 30VAC / 0.5A resistive load MTBF 62.7K HRS (MIL-HDBK-217F) DIMENSION 55.5x125.2x99.8 mm (WxHxD) PACKING 0.72kg 12pcs / 12.8kg COOLING Free air convection All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25C of ambient temperature. For the latest on Altech Power Supply specifications please visit www.altechcorp.com/power. 22PSC-151 Series Mechanical Specification Unit : mm / inch Terminal Pin No. Assignment (TB1) Assignment Pin NO. 1 FG 2 AC/L 3 AC/N Terminal Pin No. Assignment (TB2) 55.5 Assignment Pin NO. 1 DC+ 99.8 2 DC- 5 6 1 2 3 4 3 INH+ 4 INH- TB2 Relay Contact 5,6 Relay Contact + +V ADJ. Switch No. Assignment DC ON ON OFF SW1 SW NO. Assignment SW2 SW1 PEAK LOAD SETTING SW2 REMOTE ON/OFF SETTING 1 2 3 TB1 Block Diagram EMI FILTER RECTIFIERS +V PFC POWER & I/P & CIRCUIT SWITCHING -V FILTER RECTIFIERS O.C.P. FG O.L.P. O.L.P. O.L.P. DETECTION CIRCUIT AC DETECTION PWM & PFC CONTROL CIRCUIT O.V.P. MICRO Relay C CIRCUIT O.T.P. INH+ REMOTE CONTROL INH- PEAK LOAD CONTROL DC OK Relay Contact Contact Close When the output voltage reaches the adjusted output voltage. Contact Open When the output voltage drop below 45% rated output voltage. Contact Ratings(max.) 30V/1A resistive load Note: All dimensions are in millimeters, to convert to inches multiply by 0.03937. Altech Corp. 35 Royal Road Flemington, NJ 08822-6000 Phone (908)806-9400 FAX (908)806-9490 23 125.2