ADG786BCPZ Analog Devices

2.5 , 1.8 V to 5.5 V, 2.5 V Triple/Quad a SPDT Switches in Chip Scale Packages ADG786/ADG788 FEATURES FUNCTIONAL BLOCK DIAGRAMS 1.8 V to 5.5 V Single Supply 2.5 V Dual Supply 2.5 On Resistance ADG786 S1A S4A S1B 0.5 On Resistance Flatness D D1 D1 S3A 100 pA Leakage Currents S1A S4B S1B D3 19 ns Switching Times IN1 IN4 S3B Triple SPDT: ADG786 ADG788 S2A Quad SPDT: ADG788 D2 20-Lead 4 mm 4 mm Chip Scale Packages IN2 IN3 S2B Low Power Consumption S2B S3B TTL/CMOS-Compatible Inputs LOGIC D2 D3 For Functionally-Equivalent Devices in 16-Lead TSSOP S2A S3A Packages, See ADG733/ADG734 Qualified for automotive applications A0 A1 A2 EN APPLICATIONS SWITCHES SHOWN FOR A LOGIC 1 INPUT Data Acquisition Systems Communication Systems Relay Replacement Audio and Video Switching Battery-Powered Systems GENERAL DESCRIPTION PRODUCT HIGHLIGHTS The ADG786 and ADG788 are low voltage, CMOS devices 1. Small 20-Lead 4 mm 4 mm Chip Scale Packages (CSP). comprising three independently selectable SPDT (single pole, 2. Single/Dual Supply Operation. The ADG786 and ADG788 double throw) switches and four independently selectable SPDT are fully specified and guaranteed with 3 V 10% and switches respectively. 5 V 10% single supply rails, and 2.5 V 10% dual Low power consumption and operating supply range of 1.8 V to supply rails. 5.5 V and dual 2.5 V make the ADG786 and ADG788 ideal 3. Low On Resistance (2.5 typical). for battery powered, portable instruments and many other 4. Low Power Consumption (<0.01 W). applications. All channels exhibit break-before-make switch- ing action preventing momentary shorting when switching 5. Guaranteed Break-Before-Make Switching Action. channels. An EN input on the ADG786 is used to enable or disable the device. When disabled, all channels are switched OFF. These multiplexers are designed on an enhanced submicron process that provides low power dissipation yet gives high switch- ing speed, very low on resistance, high signal bandwidths and low leakage currents. On resistance is in the region of a few ohms, is closely matched between switches and very flat over the full signal range. These parts can operate equally well in either direction and have an input signal range which extends to the supplies. The ADG786 and ADG788 are available in small 20-lead chip scale packages. Rev. C Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. infringements of patents or other rights of third parties that may result from its use. Tel: 781.329.4700 20012015 Analog Devices, Inc. All rights reserved. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and Technical Support www.analog.com registered trademarks are the property of their respective owners. 1 (V = 5 V 10%, V = 0 V, GND = 0 V, unless otherwise noted.) ADG786/ADG788SPECIFICATIONS DD SS B Version 40 C Parameter +25 C to +85 C Unit Test Conditions/Comments ANALOG SWITCH Analog Signal Range 0 V to V V DD On Resistance (R ) 2.5 typ V = 0 V to V , I = 10 mA ON S DD DS 4.5 5.0 max Test Circuit 1 On-Resistance Match between 0.1 typ V = 0 V to V , I = 10 mA S DD DS Channels (R ) 0.4 max ON On-Resistance Flatness (R ) 0.5 typ V = 0 V to V , I = 10 mA FLAT(ON) S DD DS 1.2 max LEAKAGE CURRENTS V = 5.5 V DD Source OFF Leakage I (OFF) 0.01 nA typ V = 4.5 V/1 V, V = 1 V/4.5 V S D S 0.1 0.3 nA max Test Circuit 2 Channel ON Leakage I , I (ON) 0.01 nA typ V = V = 1 V, or 4.5 V D S D S 0.1 0.5 nA max Test Circuit 3 DIGITAL INPUTS Input High Voltage, V 2.4 V min INH Input Low Voltage, V 0.8 V max INL Input Current I or I 0.005 A typ V = V or V INL INH IN INL INH 0.1 A max C , Digital Input Capacitance 4 pF typ IN 2 DYNAMIC CHARACTERISTICS t 19 ns typ R = 300 , C = 35 pF ON L L 34 ns max V = 3 V, V = 0 V, Test Circuit 4 S1A S1B t 7 ns typ R = 300 , C = 35 pF OFF L L 12 ns max V = 3 V, Test Circuit 4 S ADG786 t (EN) 20 ns typ R = 300 , C = 35 pF ON L L 40 ns max V = 3 V, Test Circuit 5 S t (EN) 7 ns typ R = 300 , C = 35 pF OFF L L 12 ns max V = 3 V, Test Circuit 5 S Break-Before-Make Time Delay, t 13 ns typ R = 300 , C = 35 pF D L L 1 ns min V = 3 V, Test Circuit 6 S Charge Injection 3 pC typ V = 2 V, R = 0 , C = 1 nF S S L Test Circuit 7 Off Isolation 80 dB typ R = 50 , C = 5 pF, f = 1 MHz L L Test Circuit 8 Channel-to-Channel Crosstalk 80 dB typ R = 50 , C = 5 pF, f = 1 MHz L L Test Circuit 9 3 dB Bandwidth 160 MHz typ R = 50 , C = 5 pF, Test Circuit 10 L L C (OFF) 11 pF typ f = 1 MHz S C , C (ON) 34 pF typ f = 1 MHz D S POWER REQUIREMENTS V = 5.5 V DD I 0.001 A typ Digital Inputs = 0 V or 5.5 V DD 1.0 A max NOTES 1 Temperature range is as follows: B Version: 40C to +85C. 2 Guaranteed by design, not subject to production test. Specifications subject to change without notice. 2 REV.