ALD10F48N-L

Embedded Power for Business-Critical Continuity Rev. 08.04.11 19 ALD15 Series 1 of 3 ALD15 Series 15 Amps Total Power: 35 Watts Input Voltage: 48V of Outputs: Single Electrical Specifications Input Input ra nge: 36 to 75 Vdc Special Features Input surge: 100 V / 100 ms High Efficiency -40 C to + 85 C ambient air Efficiency: 90.5% 12 V operation Output 1.30 x 0.90 x 0.35 TH or Line regulation: 0.1% V (typical) o SMT package Load regulation: 0.1% V (typical) o High capacitive load limit on 1 Noise/ripple : 40 mVp-p (typical) start-up Industry standard feature Remote sense: Up to 10% of Vo sets: UVLO, OVP, OCP, OTP, Transient response: 3% V (typical) deviation o on/off enable, remote sense, 50% to 75% load change output trim 80 s setting time (typical) Basic insulation Overvoltage protection: 125% V typical (autorecovery) o Regulation to zero load Overcurrent protection: 115% I o typical (autorecovery) Fixed frequenc y switching Overtemperature protection: 115 C average PCB temperature (autorecovery) EU directive 2002/95/EC Switching frequency: Fixed frequency compliant for RoHS Isolation voltage: 1500 Vdc minimum (2000 Vdc ALD10F48N) Control Voltage adjust: 90 to 110% Vo Enable: TTL compatible Environmental Specifications Ambient air operating temperature range: -40 C to +85 C Storage temperature: -40 C to +125 C MTBF: 1 million hours Safety UL, cUL: 60950-1 TUV: EN60950-10.12 3.00 (8X) 0.12 3.00 (8X) Embedded Power for Business-Critical Continuity Rev. 08.04.11 19 Ordering Information ALD15 Series 2 of 3 2 Input Voltage Output Voltage Output Current Efficiency Model Number 36 - 75 V 12.0 V 2.75 A 90.5% ALD03B48(N)-(L)/(6L)/(SL) 36 - 75 V 5.0 V 7.00 A 91% ALD07A48(N)-(L)/(6L)/(SL) 36 - 75 V 3.3 V 10.00 A 90% ALD10F48(N)-(L)/(6L)/(SL) 36 - 75 V 2.5 V 11.00 A 89% ALD11G48(N)-(L)/(6L)/(SL) 36 - 75 V 1.8 V 13.00 A 87% ALD13Y48(N)-(L)/(6L)/(SL) 36 - 75 V 1.5 V 15.00 A 85% ALD15M48(N)-(L)/(6L)/(SL) 36 - 75 V 1.2 V 15.00 A 84% ALD15K48(N)-(L)/(6L)/(SL) Notes: Efficiency values taken at nominal imput full load condition, 25 C ambient temperature. TABLE2 Options MODEL PI mm ALDxxx48-L,ALDxxx48N-L 5.00.3 N = Designates Negative Logic Enable (default is Positive Enable with no suffix N required) ALDxxx48-6L,ALDxxx48N-6L 3.70.3 L = RoHS compliant ALDxxx48-8L,ALDxxx48N-8L 2.80.3 SUGGESTED PICK UP POINT -6L = 3.7 mm nominal pin length (default is 5 mm nominal pin length with no suffix -6 required), RoHS compliant -SL = Surface Mount Termination (default is thru hole termination with no suffix -S required) RoHS compliant. STRL designates Taped and Reeled option for SMT 0.04 1.0 (6x)(SEE TABLE 2 ) 0.06 1.60 2X 12.19 Mechanical Drawings Pin Assignments Through-hole Termination Single Output PIN 1 1. +Vin 0.1 2.54 1.10 27.94 2. Enable 0.9 22.860.5 1.30 33.020.5 3. -Vin TABLE2 4. -Vout MODEL PI mm 5. -Sense ALDxxx48-L,ALDxxx48N-L 5.00.3 ALDxxx48-6L,ALDxxx48N-6L 3.70.3 6. Trim ALDxxx48-8L,ALDxxx48N-8L 2.80.3 7. +Sense SUGGESTED PICK UP POINT 8. +Vout Notes: 1. 20 mHz bandwidth. External 10 F tant. 0.04 1.0 (6x)(SEE TABLE 2 ) 0.06 1.60 2X capacitor in parallel with 0.1uF ceramic 12.19 capacitor placed across + Vout and -Vout 33 F e-cap or equivalent placed across +Vin and -Vin. 2. Efficienc y measurements taken at full load, nominal line and T = 25 C 0.1 2.54 1.10 27.94 A 0.9 22.860.5 3. All specifications are typical at nominal 1.30 33.020.5 line, full load and T = 25 C unless oth- A erwise noted. 4. Mechanical drawings are for reference only. Dimensions are in inches mm . Mechanical tolerance 0.020 0.50 Surface Mount Termination 5. Technica l Reference Notes should be PIN 1 consulted for detailed information when available. 6. All specifications subject to change with- out notice. SUGGESTED PICK UP POINT 7. Warranty 2 years. 8. The through-hole terminated modules are intended for wave soldering process. 12.19 0.9 22.860.5 0.1 2.54 1.10 27.94 1.30 33.020.5 c 0.15 4 SUGGESTED PICK UP POINT 12.19 0.9 22.860.5 FOR SMD VERSION 0.1 2.54 1.10 27.94 1.30 33.020.5 c 0.15 4 1.30 33.02 1.10 27.94 1.30 33.02 0.10 2.54 1.10 27.94 0.10 2.54 FOR SMD VERSION A(2X) B(5X) RECOMMEND PAD LAYOUT FOR THROUGH HOLE VERSION (VIEW FROM TOP SIDE OF CUSTOMER RECOMMEND PAD LAYOUT FOR SMD VERSION PCB) (VIEW FROM TOP SIDE OF CUSTOMER PCB) 1.30 33.02 TABLE1 1.30 33.02 1.10 27.94 0.10 2.54 1.10 27.94 HOLE & PAD DIAMETER FOR CUSTOMER (RECOMMENDED) 0.10 2.54 HOLE DIAMETER (d) PAD DIAMETER (D) 1.9 2.9 A 1.3 2.3 B A(2X) B(5X) RECOMMEND PAD LAYOUT FOR THROUGH HOLE VERSION (VIEW FROM TOP SIDE OF CUSTOMER RECOMMEND PAD LAYOUT FOR SMD VERSION PCB) (VIEW FROM TOP SIDE OF CUSTOMER PCB) TABLE1 HOLE & PAD DIAMETER FOR CUSTOMER (RECOMMENDED) HOLE DIAMETER (d) PAD DIAMETER (D) 1.9 2.9 A 1.3 2.3 B 10.5 10.5 10.5 10.5 0.34 8.6 0.5 0.1 2.5 max. 0.60 15.24 0.34 8.6 0.5 0.34 8.6 0.5 (0.15 3.81 x4) 0.15 3.81 0.1 2.5 max. 0.1 2.5 max. 0.60 15.24 0.60 15.24 0.15 3.81 (0.15 3.81 x4)0.34 8.6 0.5 (0.15 3.81 x4) 0.15 3.81 0.15 3.81 0.1 2.5 max. 0.60 15.24 0.60 15.24 0.15 3.81 0.15 3.81 (0.15 3.81 x4) (0.15 3.81 x4) 0.15 3.81 0.15 3.81 0.60 15.24 0.15 3.81 0.15 3.81 (0.15 3.81 x4) 0.15 3.81 0.15 3.81 0.30 7.62 0.60 15.31 0.30 7.62 0.30 7.62 0.09 2.2 0.15 3.81 0.60 15.31 0.60 15.31 0.16 4.0 0.16 4.0 0.30 7.62 0.09 2.2 0.15 3.81 0.15 3.81 0.30 7.62 0.09 2.2 0.60 15.31 0.16 4.0 0.16 4.0 0.15 3.81 0.60 15.31 0.15 3.81 0.9 22.86 0.30 7.62 0.09 2.2 0.15 3.81 0.60 15.31 0.9 22.86 0.60 15.24 ( 0.15 3.81 x3) 0.15 3.81 0.60 15.24 0.15 3.81 ( 0.15 3.81 x3) 0.15 3.81 0.15 3.81 0.30 7.62 0.15 3.81 0.60 15.31 0.9 22.86 0.30 7.62 0.15 3.81 0.60 15.31 0.9 22.86