Sure Cross Wireless Q45 Sensor - Retroreflective Datasheet The sensor polarizes the emitted light and filters out unwanted reflections, making sensing possible in applications otherwise considered unsuited to retroreflective sensing. Detects objects between 0.15 m (6 in) and 6 m (20 ft) away Includes the retroreflective-mode photoelectric sensor, a wireless Node, and an internal battery to make it easy to install Aligning the visible red sensing beam is easy Counts up to 960 parts per minute Models Frequency Sensing Range Inputs and Outputs DX80N2Q45LP 2.4 GHz ISM Band 0.15 m to 6 m (6 in to 20 Photoelectric sensor with event counter ft) DX80N9Q45LP 900 MHz ISM Band Performance is specified using the model BRT-3 3-inch reflector (see the Accessories section of your current Banner catalog for further information). WARNING: Not To Be Used for Personnel Protection Never use this device as a sensing device for personnel protection. Doing so could lead to serious injury or death. This device does not include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. Storage Mode for the Q45 While in storage mode, the Q45 s radio does not operate. The Q45 ships from the factory in storage mode to conserve the battery. To wake the device, press and hold the button for five seconds. To put any Q45 into storage mode, press and hold the button for five seconds. The Q45 is in storage mode when the LEDs stop blinking. Configuration Instructions Button and LEDs 1. Button 5 2. Red LED (flashing) indicates a radio link error with the Gateway. 3. Green LED (flashing) indicates a good radio link with the Gateway. 6 4. Amber LED for Alignment or Test Mode. Indicates sensor function (optical sensor models) or when input 1 is active (dry contact models). The amber LED is not used during normal operation. 5. Excess gain potentiometer. Turn clockwise to increase the gain. 6. DIP switches 4 1 2 3 DIP Switches DIP Switch Settings 1 2 3 4 900 MHz Transmit Power Level: 1 Watt (30 dBm) OFF * 900 MHz Transmit Power Level: 250 mW (24 dBm) (DX80 Compatibility Mode) ON No Counter, 62.5 ms Sample Rate/Change of State Reporting OFF * OFF * OFF * Counter Enabled, 62.5 ms Sample Rate/1 min Report Rate OFF OFF ON Counter Enabled, 62.5 ms Sample Rate/User-Defined Report Rate OFF ON OFF Counter Enabled, 31.25 ms Sample Rate/1 min Report Rate OFF ON ON Counter Enabled, 31.25 ms Sample Rate/User-Defined Report Rate ON OFF OFF Original Document 12 September 2017 157343 Rev. E 157343 Sure Cross Wireless Q45 Sensor - Retroreflective DIP Switch Settings 1 2 3 4 Reserved ON OFF ON Reserved ON ON OFF UCT-Configured (User-Defined) ON ON ON * Default Configuration Transmit Power Levels The 900 MHz radios transmit at 1 Watt (30 dBm) or 250 mW (24 dBm). While the Performance radios operate in 1 Watt mode, they cannot communicate with the older 150 mW radios. To communicate with 150 mW radios, operate this radio in 250 mW mode. For 2.4 GHz models, this DIP switch is disabled. The transmit power for 2.4 GHz is fixed at about 65 mW EIRP (18 dBm), making the 2.4 GHz Performance models automatically compatible with older 2.4 GHz models. Sample and Report Rates The sample interval, or rate, defines how often the Sure Cross device samples the input. For battery-powered applications, setting a slower rate extends the battery life. The report rate defines how often the Node communicates the I/O status to the Gateway. For FlexPower applications, setting the report rate to a slower rate extends the battery life. Modbus Registers I/O Modbus Holding Register I/O Type I/O Range Holding Register Representation Gateway Any Node Min. Value Max. Value Min. (Dec.) Max. (Dec.) 1 1 1 + (Node 16) Sensor IN 1 State 0 1 0 1 2 2 2 + (Node 16) Reserved 3 3 3 + (Node 16) Counter High Word 0 65535 0 65535 4 4 4 + (Node 16) Counter Low Word 0 65535 0 65535 7 7 7 + (Node 16) Reserved 8 8 8 + (Node 16) Device Message 14 14 14 + (Node 16) Clear Counter 0 1 0 1 15 15 15 + (Node 16) Control Message 16 16 16 + (Node 16) Reserved Using the Event Counter The countercount when the input is on for a minimum of the sample rate. The counter input is off when the input is off for a minimum of the sample rate. Event counts For example, if your sample rate is set to 62.5 ms, the counter input is on, and therefore counts, when the input is on for at least 62.5 ms. If the input is not on for 62.5 ms, the counter does not increment. Event counter To clear the counter when you are using a host-controlled system, send a control message to does not count Node register 15. Control messages on Node register 15 are acknowledged with the same value echoed to Node register 7. t = 0 1x 2x 3x 4x 1. Write 5388 (0x150C) to Node register 15. sample sample sample sample rate rate rate rate 2. Read Node register 7 until it echoes the Node register 15 value. To clear the counter when you are not using a host-controlled system, write a 1 to the Node s output register 14. Clearing the counter requires that this register goes from a 0 to a 1. If there is already a 1 in the register, first write a 0, then write the 1. You can use the Gateway I/O mapping to map an input, such as a button, to clear the counter value. Installation Instructions Bind the Q45 to the Gateway and Assign the Node Address Before beginning the binding procedure, apply power to all the devices. 2 www.bannerengineering.com - Tel: +1-763-544-3164 P/N 157343 Rev. E