AMS22B5A1BLAFL334S Bourns

Features n RoHS compliant* n Non-contacting magnetic technology n Highly resistant to vibration/shock n Highly resistant to fluid/dust ingress n Programmable at factory for zero position n Robust design for industrial applications n Highly repeatable AMS22B Non-Contacting Analog Rotary Position Sensor 1 Electrical Characteristics ( 25 C) Product Dimensions VDD Supply Voltage ..................................................................................................5 V 10 % 10.29 +0.00/-0.05 DIA. Supply Current......................................................................................................... 20 mA max. (.4051 +.0000/-.0020) Output Signal (Single) ..................................................................................................... Analog 6.342 +0.000/-0.007 DIA. (.2497 +.0000/-.0003) Independent Linearity ...................................................... 0.5 % (0.3 % available on request) 0.25 Hysteresis .........................................................................................................0.2 % VDD max. 45 5 XCHAMFER (.010) 2 Effective Electrical Angle ..................................................................................................340 1.19 1.60 Programmable Electrical Angle .................................................. 10 to 360 (10 increments) SLOT X (.047) (.063) Voltage Output (Programmable) ................................................................ 1 to 99 % VDD 1 % 11.3 0.38 Output Resolution .................................................................................................12 bit 360 (.445 .015) 1.57 (.062) Load Resistance Recommended .......................................................................10K ohms to 3/8-32- Overvoltage Protection .................................................................................................+20 VDC UNEF 22.23 Reverse Voltage Protection ...........................................................................................-10 VDC (.875) DIA. Environmental Characteristics Operating Temperature ......................................................................................-40 to +125 C 9.53 0.78 Moisture Resistance .........................................................................MIL-STD-202, Method 106 (.375 .031) Insulation Resistance 500 VAC..........................................................................500 MW min. 0.51 22.23 0.76 Rotational Life (Shaft Revolutions) .............................................................................. 50 million (.020) (.875 .030) 3 PLCS. Vibration ..............................................................................................................................15 G 4.06 0.38 4.83 0.51 Shock...................................................................................................................................50 G (.160 .015) (.190 .002) IP Rating ..............................................................................................................................IP50 FLATTED ESD Rating ................................................................................................................. 2 kV max. OPTION Mechanical Characteristics ( 25 C) 6.35 0.08 (.250 .003) Mechanical Angle ....................................................... Continuous (340 +4/-0 stops available) Shaft/RPM ...........................................................................................................500 RPM max. 2.03 (.080) Torque 0.51 Starting & Running ......................................................................1.06 N-cm. (1.5 oz-in.) max. (.020) Mounting ........................................................................... 170-200 N-cm (15-18 lb.-in.) max. Shaft Material ...................................................................................................... Stainless steel 1.55 0.25 (.061 .010) Terminals ................................................................. Brass / 100 % matte tin over Ni Strike (e3) 1.02 Bearing .................................................................................................................Bronze sleeve 2.80 0.10 (.040) Soldering Condition (.110 .004) Manual Soldering .................................................96.5Sn/3.0Ag/0.5Cu solid wire or no-clean 45 5 rosin cored wire 370 C (700 F) max. for 3 seconds Wave Soldering ............................................. 96.5Sn/3.0Ag/0.5Cu solder with no-clean fl ux 260 C (500 F) max. for 5 seconds Figure 1 Wash processes ........................................................................................Not recommended OUTPUT VOLTAGE INCREASES WHEN SHAFT IS ROTATED IN THIS DIRECTION 1 (SEE HOW TO ORDER FOR At room ambient: +25 C nominal and 50 % relative humidity nominal, except as noted. DIRECTION CODE) 2 Other Effective Electrical Angles available. See How to Order selection guide. CCW CW 5.08 Rotational Life vs. Side Load (.200) 3 PLCS. 60 + S1 50 MEXICO GND V+ SUPPLY (GROUND) (INPUT) 40 SIGNAL 5.08 5.08 (OUTPUT) (.200) (.200) 30 MM DIMENSIONS: 20 (INCHES) 10 Schematic 0 0 50 100 150 200 250 300 350 400 450 500 + V (5 V) DD Shaft Side Load (grams) S1 V OUT GND *RoHS Directive 2015/863, Mar 31, 2015 and Annex. Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. WARNING Cancer and Reproductive Harm The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of www.P65Warnings.ca.gov this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Rotational Life (Millions of Shaft Revolutions)Applications n Tilt control and tilt positioning feedback n Patient platform positioning feedback n Foot pedal, steering, lift-and-shuttle and n Pneumatic control valve position feedback suspension systems n Draw wire position sensors n Remote communications antenna positioning n Actuator motor position feedback n Automated manufacturing robotics AMS22B Non-Contacting Analog Rotary Position Sensor How To Order AM S2 2B 5A1B HA SL 33 4 N HARD STOP Code Description MODEL DESIGNATOR N Continuous Code Description S Hard Stop (340 +4/-0 ) AM Analog Magnetic EFFECTIVE CONFIGURATION ELECTRICAL ANGLE 10 Increments Code Description S Single-turn Code Description 01 10 02 20 SIZE 03 30 Code Description 34 340 22 22 mm 35 350 36 360 MOUNTING CONFIGURATION Notes: Code Description Effective Electrical Angle Bushing Mount a vailable in 10 increments from B 7/8 Shaft FMS, a minimum of 10 to 360 maximum. 1/4 Shaft Dia. Use CodeB for 45. 60 SUPPLY VOLTAGE, V CC DIRECTION* Code Description 50 Code Description 5 5 VDC 1 CCW (Increasing Voltage) 3 CW (Increasing Voltage) 40 12 OUTPUT TYPE * See Figure 1 for clarification. Code Type Signal Resolution 10 A1 Analog Single 12 Bit 30 TERMINAL CONFIGURATION Code Description 8 INDEPENDENT LINEARITY L Axial 20 Code Description B 0.5 % 6 SHAFT STYLE C 0.3 % 10 Code Description 4 F Flatted PROCESSING SPEED S Slotted 0 Code Output Refresh Rate 2 0 50 100 150 200 250 300 350 400 450 500 H High (200 s Typ.) VOLTAGE RATIO 1 % 0 Code Description Shaft Side Load (grams) Shaded areas represent most common features. 0 50 100 150 200 250 300 350 400 450 500 A 1-99 % of VCC B 5-95 % of VCC Shaft Side Load (grams) C 10-90 % of VCC Standard Output: 1-Turn CW Increasing (Code 334 Shown) Resolution EEA Resolution EEA Resolution EEA Resolution 100 10 114 130 1479 260 2958 90 80 VOLTAGE RATIO A 20 228 140 1593 270 3072 70 30 341 150 1707 280 3186 60 50 VOLTAGE RATIO C 40 455 160 1820 290 3300 40 45 512 170 1934 300 3413 30 50 569 180 2048 310 3527 20 10 60 683 190 2162 320 3641 0 70 796 200 2276 330 3755 0 20 40 60 80 100 120 140 160 180 200 220 240 260 280 300 320340 360 80 910 210 2389 340 3868 CW DIRECTION 90 1024 220 2503 350 3982 Mechanical Angle () 100 1138 230 2617 360 4096 110 1252 240 2731 120 1365 250 2844 REV. 06/20 Specifications are subject to change without notice. Users should verify actual device performance in their specific applications. The products described herein and this document are subject to specific legal disclaimers as set forth on the last page of this document, and at www.bourns.com/docs/legal/disclaimer.pdf. Rotational Life (Millions of Cycles) Vout (%) Rotational Life (Millions of Shaft Revolutions)