FT93x Datasheet Embedded Microcontroller Datasheet Version 1.5 Document Reference No.: BRT 000051 Clearance No.: BRT 049 Future Technology Devices International Ltd. FT930/1/2/3 (Embedded Microcontroller) The FT93x series includes the FT930, FT931, FT932 SD Host Controller conformant to SDA SD Host and FT933 which are complete System-On-Chip 32-bit Controller specification V3.0, running up to 25 RISC microcontrollers for USB to multi-interface MHz and software support for SD/SDHC/SDXC bridging and embedded applications featuring a high cards level of integration and low power consumption. With a 1 I2C bus interfaces may be configured as master or D2XX hardware engine built-in, it is compatible with slave, supporting standard/fast /fast plus/high D2XX drivers. It has the following features: speed mode data transfers. Max data transfer rate High performance, low power mixed 16-bit/32-bit up to 3.4 Mbit/s. Clock stretching is supported. FT32B core processor, running at a frequency of 100MHz. Four UARTs configurable as two full UART 128kB on-chip Flash memory. interfaces or 4 half UART interfaces 128kB on-chip shadow program memory. Four 16-bit timers with prescaler and one 32-bit True Zero Wait States (0WS) up to 3.1 DMIPS per watchdog timer. MHz performance. Supports eight independent PWM channels. PWM 32kB on-chip data memory. Channel 0 and 1 may be configured as stereo audio output channels, supporting PCM 8-bit/16- Integrated Phase-Locked Loop (PLL) supports bit stereo data. single external 12MHz crystal and direct external clock source input. Supports two independent 10-bit DACs. DAC 0/1 channel output. Sample rate of ~1MS/s. Real Time Clock (RTC) with automatic calibration to compensate for inaccuracies in low-cost 32.768 Supports three 8-bit ADC1/2/3 channel input. kHz crystal or other input source. Sample rate of ~480KS/s. D2XX hardware engine (USB 2.0 Device) with up Single 3.3 volt power supply, built-in 1.2 V to 7 interfaces regulator. One USB 2.0 Device controller supports high-speed 3.3 volt I/O power supply, all GPIO pins are 5V (480 Mbit/s) and full-speed (12 Mbit/s). tolerant. USB2.0 Device controller supports Isochronous, Supports USB Battery Charging Specification Rev Interrupt, Control, and Bulk transfers for up to 15 1.2. endpoints Power-On Reset (POR). Supports One-Wire for firmware download and -40C to 85C extended operating temperature software debugging. range. One SPI Master supports single/dual/quad modes Available in compact Pb-free, RoHS compliant 68 of data transfer. Clock rate is up to 25 MHz to 48-pin packages. One SPI Slave supports single data transfer up to 25MHz. Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied Bridgetek Pte Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Bridgetek Pte Ltd, 178 Paya Lebar Road, 07-03, Singapore 409030. Singapore Registered Company Number: 201542387H 1 Used under agreement between BRT and FTDI, D2XX is the popular FTDI USB driver used on its FT2xx USB UART/FIFO Bridge platforms. It can be accessed directly or through a virtual COM port. Copyright Bridgetek Pte Ltd 1 FT93x Datasheet Embedded Microcontroller Datasheet Version 1.5 Document Reference No.: BRT 000051 Clearance No.: BRT 049 1 Typical Applications Companion with FT81x for multi-screen DAQ System Industrial automation display Medical appliances USB to multiple interface bridging (up to 15 Instrumentation end points) Motor drive and application control E-meter 1.1 Part Numbers Part Number Package FT930Q-X 68 Pin QFN, pitch 0.4mm, body 8mm x 8mm x 0.85mm, supports ADC/DAC, SD-Card, and RTC features. FT931Q-X 56 Pin QFN, pitch 0.5mm, body 8mm x 8mm x 0.85mm, supports ADC/DAC, SD-Card, and RTC features. FT932Q-X 48 Pin QFN, pitch 0.5mm, body 7mm x 7mm x 0.85mm, supports ADC/DAC and SD-Card features, no RTC feature. FT933Q-X 48 Pin QFN, pitch 0.5mm, body 7mm x 7mm x 0.85mm, supports ADC feature, no SD-Card and no RTC features. Table 1-1 FT93x Series Part Numbers Packaging codes for X: Packaging Code Part Packing Qty -R FT93x Tape and Reel 3000 -T FT930 Tray Packing 348 FT931 FT932 Tray Packing 260 FT933 Copyright Bridgetek Pte Ltd 2