HLMA-KL00 & HLMA-KH00 SunPower Series T-1 (3 mm), High Performance AlInGaP LED Lamps Data Sheet Description Features Outstanding LED Material Efficiency These untinted, non-diffused, solid state lamps utilize the latest absorbing substrate aluminum indium gallium High Light Output over a Wide Range of Currents phosphide (AlInGaP) LED technology. These materials have Low Electrical Power Dissipation a very high luminous efficiency, capable of producing high Colors: light output over a wide range of drive currents. In addi- Amber 590 nm tion, these LED lamps are at wavelengths ranging from Red-Orange 615 nm amber to red orange. Applications Package Dimensions Outdoor Message Boards 3.18 (0.125) Safety Lighting Equipment 2.67 (0.105) Signaling Applications 3.43 (0.135) 2.92 (0.115) Emitter for Emitter/Detector Applications Changeable Message Signs 4.70 (0.185) 6.35 (0.250) 4.19 (0.165) Portable Equipment 5.58 (0.220) Medical Equipment Automotive Lighting 1.02 NOM. (0.040) Alternative to Incandescent Lamps 0.45 SQUARE 24.10 MIN. (0.018) NOMINAL (0.95) 1.27 NOM. (0.050) 2.54 NOM. (0.100) CATHODE NOTES: 1. ALL DIMENSIONS ARE IN MILLIMETERS (INCHES). 2. AN EPOXY MENISCUS MAY EXTEND ABOUT 0.8 MM (0.032 ) DOWN THE LEADS, UNLESS OTHERWISE NOTED.Device Selection Guide Dominant Wavelength Luminous Intensity Luminous Intensity Part Number Color ld (nm) Typ Iv (mcd) at 20 mA-Min Iv (mcd) at 20 mA-Max HLMA-KL00-I0000 Amber 590nm 42.3 - HLMA-KH00-J0000 Red Orange 615nm 39.6 - Tolerance for each intensity bin limit is 15%. Absolute Maximum Ratings at T = 25C A Parameter Value Unit 1,4,5 DC Forward Current 50 mA 2 Peak Forward Current 200 mA 2 Time Average Input Power 103 mW 3 Transient Forward Current (10 ms Pulse) 500 mA Reverse Voltage (I = 100 mA) 5 V R Operating Temperature Range -40 to 100 C Storage Temperature -40 to 100 C Junction Temperature 110 C Notes: 1. Derate linearly as shown in Figure 4. 2. Any pulsed operation cannot exceed the Absolute Max Peak Forward Current or the Max Allowable Time Average Power as specified in Figure 5. 3. The transient peak current is the maximum nonrecurring peak current the device can withstand without damaging the LED die and wire bonds. 4. Drive Currents between 10 mA and 30 mA are recommended for best long term performance. 5. Operation at currents below 10 mA is not recommended, please contact your Avago Technologies sales representative. Optical Characteristics at T = 25C A Luminous Peak Color, Dominant Viewing Luminous Intensity Wavelength Wavelength Angle Part Luminous Flux (mlm) 1 2 3 IV (mcd) 20 mA lpeak (nm) ld (nm) 2q Degrees Number Efficacy 20 mA HLMA- Min, Typ. Typ. Min. Max. Typ. hv (lm/w) Typ. KL00 35 200 592 584.5 597.0 45 480 500 KH00 35 200 621 611.0 623.0 45 263 500 Notes: 1. The luminous intensity, Iv, is measured at the mechanical axis of the lamp package. The actual peak of the spatial radiation pattern may not be aligned with this axis. 2. The dominant wavelength, d, is derived from the CIE Chromaticity Diagram and represents the color of the device. 3. q1/2 is the off-axis angle where the luminous intensity is 1/2 the peak intensity. Electrical Characteristics at T = 25C A (ns) Forward Voltage Reverse Breakdown Capacitance Speed of ResponseTs VF (Volts) VR (Volts) C (pF) VF = 0, Time Constant Thermal -t/ts IF = 20 mA IR = 100 mA f = 1 MHz e Resistance PART NUMBERHLMA- Typ. Max. Min. Typ. Typ. RQJ-PIN (C/W) Typ. KL00 1.9 2.4 5 25 40 290 13 KH00 1.9 2.4 5 25 40 290 13 2