V19 LDP60 SERIES 60WATT OUTPUT LED POWER SUPPLY Features * 60W Single / Dual outputs * Universal AC input range 90~305Vac * Constant Current Design * Active PFC > 0.9 * Low inrush current < 5A * Standby Power Consumption <0.5W * Low Profile with 25.2mm Height and Narrow 40mm Width * Low Frequency Flicker Design * Continuous Short Circuit Protection * Over Temperature Protection * IP 67 Rated * Fully Isolated Plastic Case * Dimming Function: DALI/PWM/1~10VDC/Potentiometer Output Constant Ripple and Output No Load Output Output %EFF MODEL Rated Current Noise(Vp-p Rated Voltage Rated (typ.) Voltage Region max.) Current (max.) Power LDP60A240-C250BR 24V 9-24Vdc 0.24V 85% 2500mA 29Vdc 60.0W LDP60A240-C250B 24V 16-24Vdc 2.2V 88% LDP60A240-C210BR 24V 9-24Vdc 0.24V 84% 2100mA 29Vdc 50.4W LDP60A240-C210B 24V 16-24Vdc 2.2V 87% LDP60A240-C175BR 24V 9-24Vdc 0.24V 84% 1750mA 29Vdc 42.0W LDP60A240-C175B 24V 16-24Vdc 2.2V 86% LDP60A360-C166BR 36V 9-36Vdc 0.36V 85% 1666mA 43Vdc 60.0W LDP60A360-C166B 36V 24-36Vdc 2.7V 89% LDP60A360-C140BR 36V 9-36Vdc 0.36V 84% 1400mA 43Vdc 50.5W LDP60A360-C140B 36V 24-36Vdc 2.7V 88% LDP60A480-C125BR 48V 9-48Vdc 0.48V 86% 1250mA 56Vdc 60.0W LDP60A480-C125B 48V 32-48Vdc 4.8V 90% LDP60A480-C105BR 48V 9-48Vdc 0.48V 85% 1050mA 56Vdc 50.4W LDP60A480-C105B 48V 32-48Vdc 4.8V 89% V1 1250mA 29Vdc 30.0W LDP60B240-C125BR 24V 9-24Vdc 0.24V 85% V2 1250mA 29Vdc 30.0W V1 1050mA 29Vdc 25.2W LDP60B240-C105BR 24V 9-24Vdc 0.24V 84% V2 1050mA 29Vdc 25.2W V1 833mA 43Vdc 30W LDP60B360-C083BR 36V 9-36Vdc 0.36V 85% V2 833mA 43Vdc 30W V1 700mA 43Vdc 25.2W LDP60B360-C070BR 36V 9-36Vdc 0.36V 84% V2 700mA 43Vdc 25.2W V1 625mA 56Vdc 30W LDP60B480-C062BR 48V 9-48Vdc 0.48V 87% V2 625mA 56Vdc 30W All specifications are Typical at nominal line, full load and 25C unless otherwise noted 1 V19 Order Information: Series Output(W) O/P: Single/Dual Output Voltage Dimming Function Rated Output Current Input Voltage Ripple Nosie LDP 60 X XXX X XXX B X 250: 2500mA 24V 240 24V 210: 2100mA 175: 1750mA A Single O/P with IP67 166: 1666mA 36036V 36V CNo dimming R 1% output 140: 1400mA DDALI dimming ripple and noise 125: 1250mA 48048V or B 100-277 Vac P PWM 1-10V, 48V 105: 1050mA Blank10% output Potentiometer 125: 1250mA ripple and noise 24024V 24V 105: 1050mA BDual O/P 082: 833mA 36036V 36V with IP67 070: 700mA 48V 480 48V 062: 625mA Specifications LDP60 Series Derating Curve INPUT SPECIFICATIONS: AC Input Voltage ........................................... 90~305Vac Frequency .... 50/60Hz Power Factor ... PF 0.9 115Vac/230Vac, 75%~100% Load Inrush Current ..... <5A after 100us 240Vac, Cold Start 25Ta Cold Start Leakage Current ........ 0.75mA max. Standby Power Consumption .. <0.5W (No Dimming) Input Current (Full Load) .. 0.69A/0.32A typ. 115Vac/230Vac OUTPUT SPECIFICATIONS: Maximum Output Voltage .. See Table. Constant Current Accuracy (note1) ....5% max. Current Line Regulation (note2) . 5% max. Current Load Regulation (note3) ..... 5% max. Over Voltage Protection .... TVS Clamp Short Circuit Protection ...... Hiccup Mode, Auto Recovery Over Temperature Protection .... 105 typ. GENERAL SPECIFICATIONS: Efficiency ...... See Table. Temperature Coefficient ................ 0.05%/(0~50) Isolation Voltage, Input to Output ........ 3.75KVac. 8 Isolation Resistance, Input to Output .. 10 min. Operating Ambient Temperature ................ -40 ~ 70(See Derating Curve). Cooling ... Natural Convection. Storage Temperature ...................... -40 ~ 85. Operating Humidity ............. 20%~95% RH Non-Condensing. Operating Altitude . Sea Level to 3000m NOTE: MTBF, MIL-HDBK-217F (25 Ta) ... 200Khrs. 1. Current accuracy is set at nominal input voltage and full load. 2. Current line regulation is measured from high line to low line with full load. MECHANICAL CHARACTERISTICS: Dimensions ....... 10.315x1.575x0.992 Inches (262.00x40.00x25.20mm). 3. Current Load regulation is measured minimum to maximum of the Weight .... 530g. constant current region. 4. All specifications are typical at 230Vac, vo max., full load and 25 SAFETY AND EMISSIONS: Safety .............................................. UL8750, IEC61347-1, IEC61347-2-13 unless other noted. EMI ............ FCC Part 15/EN55015 Class B 5. The input/output wires accessibility shall be evaluated during final EMS .................................. EN61547, EN61000-4-2, 3, 4, 5, 6, 8, 11 system assembly. EN61000-3-2 Harmonic Class C, EN61000-3-3 All specifications are Typical at nominal line , full load and 25C unless otherwise noted 2