FFFF EEEE DDDD CCCC BBBB AAAA c b NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI ( 5 : 1 ) FOR 30 MINUTES DDDD DDDD AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICON BLUE 7. RUBBER GASKET: TPE BLACK 8. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 9. CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): b o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 2 for 20in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 10. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL 0,25 + PCB-HOLE: n3,1 0,1 PCB THICKNESS 1,6mm 8,23 - 0 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. PCB-HOLE DRILLINGS and RUBBER GASKET RECOMMENDED PANEL CUT-OUT ON SHEET 2 PLACED ON TOP SURFACE 13. RECOMMENDED TORQUE FOR MOUNTING SCREW CC CC CC CC OF MALE INSULATOR 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 14. CONNECTOR IS PART MARKED: 15-00043o CONEC ABC (see note 9) +0,3 b 61,4 - 0 47,04 0,13 POS. 1 +0,23 38,86 - 0,02 POS. 15 BBBB BBBB n0,6 0,05 (25x) b SEALING COMPOUND O-RING 15-00043o CONEC ABC 4-40 UNC SEE NOTE 14 SW 4,8 4-40 UNC scale: 2:1 (5:1) tolerance material: see notes dim. in mm AAAA AAAA date name title: b drawn 17.10.2008 Schmidt D-SUB MALE AT ALL TIMES WATER RESISTANT appd. 21.10.2008 Fischer 25pos. SOLDER PIN STRAIGHT CONNECTORS NOT IN USE norm with rear spacer clip and hexlocking screw SHOULD BE COVERED WITH A dwg no: 2 x c 5528 10.02.15 Heinrich d-old DIN- CONEC WATER RESISTANT CAP 5 x b 3435 21.02.09 HS A3 OR WATER TIGHT HOOD. RR RR 15K1A290 a Original sh: 1 c RoHS compliant rev. description date name part no: 15-00043o(see note 9) FFFF EEEE DDDD CCCC BBBB AAAA 10 0,3 + 21,1 - 0 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND +0,4 11,5 - 0,3 +0,4 11,2 - 0,3 +0 +0,4 5,99 8,6 - - 0,3 0,3 4,6 +0,25 3,6 - 9,4 0R3,4 0,13 FFFF EEEE DDDD CCCC BBBB AAAA P.C.B. HOLE DRILLINGS 0,13 47,04 DDDD DDDD 0,1 16,56 13,82 0,1 11,05 0,1 8,28 0,1 5,54 0,1 2,77 0,1 1 0,1 + n3,1 0,1 (2x) n1 (25x) 0,1 - 1,4 0 0,1 4,14 CC CC CC CC 6,91 0,1 9,68 0,1 12,42 0,1 15,19 0,1 RECOMMENDED PANEL CUT-OUT 42,5 0,1 i 0,26 A BBBB BBBB B i 0,26 B 0,1 47,04 A scale: 4:1 tolerance material: see sheet 1 dim. in mm AAAA AAAA date name title: drawn 17.10.2008 Schmidt P.C.B HOLE DRILLINGS appd. 21.10.2008 Fischer PANEL CUT-OUT norm D-SUB Male 25pos. Solder pin straight dwg no: d-old DIN- A3 RR RR 15K1A290 a Original sh: 2 rev. description date name part no: see sheet 1 FFFF EEEE DDDD CCCC BBBB AAAA 1 10 n3,1 0,05 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1 1,42 0,1 0,1 2,84