F E D C B A b NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI ( 5 : 1 ) FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE D D 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for 8in HARD GOLD over min. 50in NICKEL 9. REAR SPACER CLIPS: COPPER ALLOY b min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1 PCB THICKNESS 1,6mm 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. PCB-HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00045o CONEC ABC +0,02 8 - 0,23 +0,3 b 39,4 - 0 +0,12 25 - 0,13 C C +0 16,46 - 0,25 b 0,05 n0,64 (9x) SEALING COMPOUND B B O-RING 15-00045o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC b AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. scale: 2:1 (5:1) tolerance material: see notes dim. in mm A A date name title: drawn 17.10.2008 Schmidt D-SUB FEMALE appd. 21.10.2008 Fischer 9pos. SOLDER PIN STRAIGHT norm with rear spacer clip and hexlocking screw dwg no: d-old Inventor 10 DIN- 5 x b 3435 21.09.09 HS A3 R 15K1A276 a Origin sh: 1 rev. description date name part no: 15-00045o (see note 8) F E D C B A 10 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND +0,3 21,1 - 0 4,6 +0,4 11,93 - 0,3 9,4 +0,4 11,5 - 0,3 +0,17 +0,4 6,13 8,6 - - 0,08 0,3 +0,25 3,6 - 0R 0,13 3,4 F E D C B A D D P.C.B. HOLE DRILLINGS 0,12 + 25 - 0,13 5,49 0,1 n3,1 0,1 (2x) 2,74 0,1 1 +0,1 n1 (9x) - 0 1,37 0,1 C C 0,1 4,11 RECOMMENDED PANEL CUT-OUT 0,1 20,5 0,26 i A B B B 0,26 i B 0,1 25 A scale: 5:1 tolerance material: see sheet 1 dim. in mm A A date name title: drawn 17.10.2008 Schmidt P.C.B. HOLE DRILLINGS appd. 21.10.2008 Fischer PANEL CUT-OUT norm D-SUB Female 9pos. Solder pin straight dwg no: d-old Inventor 10 DIN- A3 R 15K1A276 a Origin sh: 2 rev. description date name part no: see sheet 1 F E D C B A 1 10 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,05 n3,1 (2x) 1,42 0,1 11,4 0,1 2,84 0,1