APPROVAL FREIGABE DEBLOCAGE AUTORIZACION F E D C B A NOTES: n1,16 (37x) 1. RECOMMENDED SOLDER INSTRUCTION SEE SHEET 2 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING ( 5 : 1 ) 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0, BLACK D 6. O-RING: SILICONE PER ASTM D2000 70 SHORE A D 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for 8in HARD GOLD over min. 50in NICKEL SOLDER CUP ACCEPTS CABLE AWG 20 9. HEXLOCKING SCREWS: STAINLESS STEEL 10. RECOMMENDED PANEL CUT-OUT ON SHEET 2 b 11. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max.67Ncm (6 in.LB) 12. CONNECTOR IS PART MARKED: 15-00064 o CONEC ABC +0,02 8 - 0,23 +0,3 b 78 - 0 0,13 63,5 C C +0 54,96 - 0,25 SEALING COMPOUND B B O-RING 15-00064 o CONEC ABC 4-40 UNC SEE NOTE 12 SW 4,8 4-40 UNC b AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. APPROVAL FREIGABE DEBLOCAGE AUTORIZACION APPROVAL scale: 2:1 (5:1) tolerance CUSTOMER APPROVAL DATE: material: see notes dim. in mm A A date name title: drawn 17.10.08 Petker D-SUB FEMALE NAME: TITLE: appd. 22.10.08 Fischer 37pos. SOLDER CUP norm with hexlocking screw dwg no: d-old Inventor 10 DIN- COMPANY NAME: 3 x b 3435 30.09.09 HS A3 R 15K1A314 aOrigin sh: 1 APPROVAL FREIGABE DEBLOCAGE AUTORIZACION APPROVAL rev. description date name part no: 15-00064 o (see note 8) F E D C B A 10 APPROVAL FREIGABE DEBLOCAGE AUTORIZACION +0,3 21,1 - 0 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND +0,17 +0,4 6,13 10,34 - - 0,3 0,08 +0,25 3,6 - 0 4,6 9,4APPROVAL FREIGABE DEBLOCAGE AUTORIZACION R3,4 0,13 F E D C B A D D Solder Instruction 1. Cable should be prepared for soldering. The cable/wires must be pretinned. 2. Insert cable/wire into solder cup. 3. Operate the soldering iron at 350C, 50 Watt max. and use a pencil tip. 4. Put tip to wire in solder cup. 5. After 1 second bring in solder. 6. Heat for 3 seconds longer. Do not heat contact more than 4 seconds in total. 7. Remove soldering iron. 8. Wait until solder gets rigid again. 9. Do not solder adjacent contacts consecutively, alternate position within the connector to minimize heat build up. C C RECOMMENDED PANEL CUT-OUT 59,1 0,1 i 0,26 A B B B 0,26 i B 0,1 63,5 A APPROVAL FREIGABE DEBLOCAGE AUTORIZACION APPROVAL scale: 3:1 tolerance CUSTOMER APPROVAL DATE: material: see sheet1 dim. in mm A A date name title: drawn 17.10.08 Petker PANEL CUT-OUT NAME: TITLE: appd. 22.10.08 Fischer D-SUB FEMALE 37pos. SOLDER CUP norm with hexlocking screw dwg no: d-old Inventor 10 DIN- COMPANY NAME: A3 R 15K1A314 aOrigin sh: 2 APPROVAL FREIGABE DEBLOCAGE AUTORIZACION APPROVAL rev. description date name part no: see sheet 1 F E D C B A 1 10 APPROVAL FREIGABE DEBLOCAGE AUTORIZACION 0,05 (2x) 3,1 n THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 11,4