F E D C B A ( 5 : 1 ) AT ALL TIMES WATER RESISTANT 0,05 n0,64 (9x) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING D D COMPOUND 0,3 + 30,88 b - 0,15 +0,12 25 - 0,13 +0 16,46 - 0,25 SEALING GASKET +0,02 8 - 0,23 b C C 15-00649o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC c B B NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00649o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 06.10.14 Lehmenkhler D-SUB FEMALE appd. 26.01.15 Fischer 9pos. SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: 1 x c 5827 25.09.15 Unkrer d-old DIN- 2 x b 5800 04.09.15 M.H. A3 R 15K1A1548 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00649o (see note 8) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH +0,4 DO NOT ALTER CAD DRAWING BY HAND 8,95 - 0,3 0,4 + 11,85 - 0,3 +0,4 12,35 - 0,3 +0,25 2,55 - 0 0,17 + 5,78 - 0,08R3,4 0,13 F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) D D +0,12 25 - 0,13 5,49 0,1 n3,1 0,1 (2x) 2,74 0,1 1 +0,1 n1 (9x) - 0 0,1 1,37 4,11 0,1 C C RECOMMENDED PANEL CUT-OUT 20,5 0,1 i 0,26 A B B B 0,26 i B 0,1 25 A scale: 5:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 06.10.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB FEMALE 9pos. SOLDER PIN STRAIGHT dwg no: d-old DIN- A3 R 15K1A1548 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 0,05 (2x) n3,1 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 1,42 0,1 0,1 11,4 0,1 2,84