F E D C B A AT ALL TIMES WATER RESISTANT ( 5 : 1 ) n0,64 0,05 (25x) CONNECTORS NOT IN USE SHOULD BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. SEALING D D COMPOUND +0,3 b 53,09 - 0,15 47,04 0,13 +0 38,5 - 0,25 SEALING GASKET +0,02 8 - 0,23 b C C 15-00651o CONEC ABC 4-40 UNC SEE NOTE 13 SW 4,8 4-40 UNC c B B NOTES: 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER SOLDERING 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART-NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. REAR SPACER CLIPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 10. HEXLOCKING SCREWS: STAINLESS STEEL 11. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 12. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 13. CONNECTOR IS PART MARKED: 15-00651o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 25.09.14 Lehmenkhler D-SUB FEMALE appd. 26.01.15 Fischer 25pos. SOLDER PIN STRAIGHT norm with closed 4-40 UNC thread and rear spacer clip dwg no: 1 x c 5827 25.09.15 Unkrer d-old DIN- 2 x b 5800 07.09.15 M.H. A3 R 15K1A1550 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00651o (see note 8) F E D C B A 10 +0,3 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 0,4 + + 12,35 8,95 - 0,3 - 0,3 +0,4 +0,25 11,85 2,55 - 0,3 - 0 0,17 + 5,78 - 0,08R3,4 0,13 F E D C B A P.C.B. HOLE DRILLINGS ( P.C.B. TOP SIDE ) 0,13 47,04 D D 0,1 16,56 13,82 0,1 11,05 0,1 8,28 0,1 5,54 0,1 n3,1 0,1 (2x) 2,77 0,1 1 0,1 + n1 (25x) 0,1 - 1,4 0 0,1 4,14 C C 6,91 0,1 9,68 0,1 12,42 0,1 15,19 0,1 RECOMMENDED PANEL CUT-OUT 0,1 42,5 i 0,26 A B B B i 0,26 B 47,04 0,1 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 25.09.14 Lehmenkhler P.C.B. HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB FEMALE 25pos. SOLDER PIN STRAIGHT dwg no: d-old DIN- A3 R 15K1A1550 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 0,05 ) n3,1 (2x THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 11,4 0,1 0,1 1,42 0,1 2,84