F E D C B A +0,5 3,3 6,35 0,3 - 0,3 AT ALL TIMES WATER RESISTANT CONNECTORS NOT IN USE SHOULD ( 5 : 1 ) BE COVERED WITH A CONEC WATER RESISTANT CAP OR WATER TIGHT HOOD. D D SEALING COMPOUND +0,3 c 53,09 - 0,15 47,04 0,13 +0 38,5 - 0,25 SEALING GASKET 0,02 + c 8 - 0,23 n0,6 0,05 (25x) C C 3,2 0,2 PRESS FOR METAL BRACKET b FIXING ON PCB PCB SNAP 15-00661o CONEC ABC 4-40 UNC b SEE NOTE 15 SW 4,8 4-40 UNC d b NOTES: B B 1. FOR WAVESOLDERING (SOLDER BATH TEMPERATURE 265C FOR 8 SEC. AND SOLDER PREHEAT 150C FOR 180 SEC.) 2. IP RATING: IP 67 3. SEALED TO WITHSTAND PRESSURE UP TO 1,45 PSI FOR 30 MINUTES AFTER HIGH TEMPERATURE EXPOSURE 4. METALSHELL: ZINC DIE CAST min. 50in NICKEL PLATING over COPPER 5. INSULATORS: PBT GF UL 94 V-0 BLACK 6. SEALING GASKET: SILICONE BLUE 7. SEALING COMPOUND: EPOXY RESIN UL 94 V-0 BLACK 8. CONTACTS: COPPER ALLOY PLATING (SEE PART NO.): o PLEASE ADD 1 for 30in HARD GOLD over min. 50in NICKEL o PLEASE ADD 3 for GOLD FLASH over NICKEL 9. METAL BRACKETS: ZINC DIE CAST 300in COPPER/40-120in NICKEL/120-200in TIN 10. WASHERS: COPPER ALLOY 80in NICKEL 11. HEXLOCKING SCREWS: STAINLESS STEEL 12. PCB-SNAPS: COPPER ALLOY min. 200in TIN over 80in NICKEL PCB-HOLE: n3,1 0,1mm PCB THICKNESS 1,6mm 13. P.C.B. HOLE DRILLINGS and RECOMMENDED PANEL CUT-OUT ON SHEET 2 14. RECOMMENDED TORQUE FOR MOUNTING SCREW 35Ncm (3.1 in.LB) / max. 67Ncm (6 in.LB) 15. CONNECTOR IS PART MARKED: 15-00661o CONEC ABC (see note 8) scale: 2:1 (5:1) tolerance material: SEE NOTES dim. in mm A A date name title: drawn 25.09.14 Lehmenkhler D-SUB FEMALE 90 appd. 26.01.15 Fischer 25pos. SOLDER PIN ANGLED d b norm with closed 4-40 UNC thread,metal bracket,snap 2 x d 5827 25.09.15 Unkrer dwg no: 2 x c 5800 07.09.15 M.H. d-old DIN- 4 x b 5793 02.09.2015 K.H. A3 R 15K1A1556 a Original sh: 1 RoHS compliant rev. description date name part no: 15-00661o (see note 8) F E D C B A 10 0,3 + 12,8 - 0,15 4,6 9,4 THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,4 + 9,6 - 0,3 +0,4 11,18 - 0,3 0,4 + 13,85 - 0,3 +0,4 8,34 - 0,3 +0,25 2,55 - 0 +0,17 5,78 - 0,080 R3,4 ,13 F E D C B A P.C.B. HOLE DRILLINGS (P.C.B. TOP SIDE) 47,04 0,13 D D 16,56 0,1 13,82 0,1 11,05 0,1 8,28 0,1 5,54 0,1 0,1 + n3,1 0,1 (2x) n1 (25x) 2,77 0,1 - 0 1 0,1 1,4 P.C.B. EDGE C C FRONTPANEL 4,14 0,1 6,91 0,1 9,68 0,1 0,1 12,42 15,19 0,1 RECOMMENDED PANEL CUT-OUT 42,5 0,1 i 0,26 A B B B i 0,26 B 47,04 0,1 A scale: 4:1 tolerance material: SEE SHEET 1 dim. in mm A A date name title: drawn 25.09.14 Lehmenkhler P.C.B HOLE DRILLINGS appd. 26.01.15 Fischer RECOMMENDED PANEL CUT-OUT norm D-SUB Female 90 25pos. Solder pin angled dwg no: d-old DIN- A3 R 15K1A1556 a Original sh: 2 rev. description date name part no: SEE SHEET 1 F E D C B A 1 10 9,6 6,75 0,05 n3,1 (2x) THIS DRAWING MAY NOT BE COPIED OR REPRODUCED IN ANY WAY, AND MAY NOT BE PASSED ON TO A THIRD PARTY WITHOUT WRITTEN PERMISSION. OWNERSHIP AND COPYRIGHT OF CONEC GmbH DO NOT ALTER CAD DRAWING BY HAND 0,1 5,49 11,4 0,1 2,84 0,1