PI3CH200 2-Bit Bus Switch, Enable Low 1.8V/2.5V/3.3V, High-Bandwidth, Hot Plug Features Description Near-Zero propagation delay The PI3CH200 is a low voltage, 2-channel switch 5-ohm switches connect inputs to outputs designed with fast individual enables. The switch High signal passing bandwidth (500 MHz) introduces no additional ground bounce noise or Beyond Rail-to-Rail switching additional propagation delay. - 0 to 5V switching with 3.3V power supply The PI3CH200 device has active low enables. It is - 0 to 3.3V switching with 2.5V power supply very useful in switching signals that have high 5V I/O tolerant with supply in OFF and ON state bandwidth (500 MHz). 1.8V, 2.5V and 3.3V supply voltage operation Applications Hot Insertion Capable High Bandwidth Data Switching Industrial Operating Temperature: -40C to +85C Hot-Docking 8kV ESD Protection (human body model) Analog Signal Switching Latch-up Performance: >200mA per JESD17 Differential Signal Switching Packaging (Pb-free & Green available): -8-pin TSSOP (L) Block Diagram Pin Configuration EN 1 A B 2 2 EN 2 Pin Description (1) Truth Table Pin No Pin Name Description 1111111 1, 7 Switch Enables EN x Ax Bx V EN EN CC Function 1, 2 2, 5 A1, A2 A Ports X Hi-Z Hi-Z GND Disconnect H Hi-Z Hi-Z V 3, 6 B1, B2 B Ports CC Disconnect 4 L Bx Ax V Connect GND Ground CC Note: 8 V Power CC 1. H=High Voltage Level L=Low Voltage Level Hi-Z=High Impedance 2014-03-0001 PT0479-2 04/18/14 1 PI3CH200 2-Bit Bus Switch, Enable Low1.8V/2.5V/ 3.3V, High-Bandwidth, Hot Plug Maximum Ratings Note: o o Stresses greater than those listed under MAXIMUM Storage Temperature ................................................................................... -65 C to +150 C RATINGS may cause permanent damage to the Ambient Temperature with Power Applied........................................ 40C to +85C device. This is a stress rating only and functional Supply Voltage to Ground Potential ............................................................ -0.5V to + 4.6V operation of the device at these or any other condi- DC Input Voltage ............................................................................................ -0.5V to + 6.0V tions above those indicated in the operational sec- DC Output Current .......................................................................................... 120mA tions of this specification is not implied. Exposure Power Dissipation .............................................................................................................. 0.5W to absolute maximum rating conditions for extended periods may affect reliability. DC Electrical Characteristics 3.3V supply (Over operating range, T = -40 ~ +85C, V =3.3V10%, unless otherwise noted) A CC (1) (2) Symbol Description Test Conditions Min Typ Max Unit V Control Input HIGH Voltage Guaranteed Logic HIGH Level 2.0 - - V IH V Control Input LOW Voltage Guaranteed Logic LOW Level -0.5 - 0.8 V IL V Clamp Diode Voltage V = Min., I = -18mA - -1.3 -1.8 V IK CC IN I Input HIGH Current V = Max., V = V - - 1 A IH CC IN CC I Input Low Current V = Max., V = GND - - 1 A IL CC IN I High-Impedance Current 0 A, B V - - 1 A OZH CC V = Min., V = 0.0V CC IN - 4 6 I = -48mA or -64mA (3) ON R Switch On-Resistance ON V = Min., V = 3.6V CC IN - 5 8 I = -15mA ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 3.3V, T = 25C ambient and maximum loading. CC A 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. 2.5V supply (Over operating range, T = -40 ~ +85C, V =2.5V10%, unless otherwise noted) A CC (1) (2) Symbol Description Test Conditions Min Typ Max Unit V Control Input HIGH Voltage Guaranteed Logic HIGH Level 1.8 - V +0.3 V IH CC V Control Input LOW Voltage Guaranteed Logic LOW Level -0.3 - 0.8 V IL V Clamp Diode Voltage V = Max., I = -6mA - -0.7 -1.8 V IK CC IN I Input HIGH Current V = Max., V = V - - 1 A IH CC IN CC I Input Low Current V = Max., V = GND - - 1 A IL CC IN I High-Impedance Current 0 A, B V - - 1 A OZH CC V = Min., V = 0.0V CC IN - 4 8 I = -48mA (3) ON R Switch On-Resistance ON V = Min., V = 2.25V CC IN - 7 14 I = -15mA ON Notes: 1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type. 2. Typical values are at V = 2.5V, T = 25C ambient and maximum loading. CC A 3. Measured by the voltage drop between A and B pin at indicated current through the switch. On-Resistance is determined by the lower of the voltages on the two (Ax, Bx) pins. 2014-03-0001 PT0479-2 04/18/14 2