JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 R3 R3 R3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 R3 R3 R3 Sample ELK-960 Hookups (set jumpers as shown) 12/24 Volts DC 12/24 Volts DC DOOR STRIKE HOLD MAGLOCK RELEASE 1 2 Power Supply Power Supply TIMER TIMER - + - + TIME 1 - 60 TIME 1 - 60 ELK-960 ELK-960 SEC SEC Delay Timer Delay Timer MIN MIN TRIGGER TRIGGER + + POLARITY POLARITY - - REPEAT REPEAT - + - + 12/24V 12/24V DOOR 1-SHOT 1-SHOT MAGLOCK TGR TGR STRIKE JP5 JP5 N/O N/O END END + + N/O N/O Pushbutton Pushbutton BEGIN BEGIN TRIGGER TRIGGER COM K1 COM K1 MODE MODE N/C N/C A A B B LED JP4 LED JP4 Used to extend the release time of an access control device Used to extend the release time of an access control device or to manually activate a door strike release device. The or to manually activate a door maglock release device. The trigger is activated by a contact closure or a N/O pushbutton trigger is activated by a contact closure or a N/O pushbutton and the door strike remains activated (door open) after the and the door maglock remains released (door open) after the button is released for the delay time set up in the ELK-960. button is released for the delay time set up in the ELK-960. 12 Volts DC AUTOMATIC LIGHT BELL OR LIGHT CONTROL PANEL Power Supply 3 4 Motion 12V ALARM - + CONTROL FLASHER Detector OUTPUT TIME 1 - 60 - + TIME 1 - 60 ELK-960 ELK-960 SEC SEC - Delay Timer Delay Timer + MIN MIN TRIGGER TRIGGER COM + + POLARITY POLARITY REPEAT REPEAT N/C - + - + 22K Ohm 1-SHOT 1-SHOT Resistor TGR TGR JP5 JP5 12V END END Hot N/O N/O 120VAC LIGHT Supply BEGIN BEGIN or LED TRIGGER TRIGGER COM K1 COM K1 MODE MODE 12V Bell N/C N/C A A or Siren 120V B B LIGHT + - + - LED JP4 LED JP4 Neutral Converts a steady output to pulsing, suitable for flashing a For turning on an interior or exterior light with a motion light or pulsing an audible device. Note: Alarm output must be detector. When motion is detected, the ELK-960 is triggered capable of supplying enough current to drive the bell and and the light is turned on. The amount of time the light remains light. on after the detector resets is adjustable. Delay time will automatically restart each time the motion detector activates. ALARM CUT-OFF EXIT DELAY CONTROL PANEL CONTROL PANEL 5 6 12V ALARM CLOSED TIMER SHUNT TIMER OUTPUT ZONE + ARMED 12V AUX - + TIME 1 - 60 INPUT OUTPUT TIME 1 - 60 - + ELK-960 ELK-960 SEC SEC Delay Timer Delay Timer MIN MIN TRIGGER TRIGGER + + POLARITY POLARITY REPEAT REPEAT - + - + 1-SHOT 1-SHOT TGR TGR JP5 JP5 END END N/O N/O BEGIN BEGIN TRIGGER TRIGGER COM K1 COM K1 MODE MODE N/C N/C 12V Bell A A N/C - + or Siren B B CONTACT ON EXIT DOOR LED JP4 LED JP4 Provides an exit delay to an otherwise instant alarm loop. Useful for adding a cut-off timer to a control panel that does The ELK-960 is triggered by the control s Armed output. The not have one. It can also be used to shorten the cut-off timer door contact is then shunted by the relay contacts. After the for a control with no adjustable timer. user has exited and the delay time has expired, the door contact is restored into the loop. - - - - - -JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 R3 R3 R3 JP1 JP2 JP3 JP1 JP2 JP3 JP1 JP2 JP3 R3 R3 R3 12 Volts DC DOOR PROP ALARM DELAY AUDIABLE CONTROL PANEL 7 8 Power Supply 12V ALARM TIMER ALARMS OUTPUT - + TIME 1 - 60 - + TIME 1 - 60 ELK-960 ELK-960 SEC SEC Delay Timer Delay Timer MIN MIN SIREN TRIGGER TRIGGER + + POLARITY POLARITY - REPEAT REPEAT - + - + 1-SHOT 1-SHOT + TGR TGR JP5 JP5 N/C END END N/O N/O CONTACT ON BEGIN BEGIN DOOR TRIGGER TRIGGER COM K1 COM K1 MODE MODE N/C N/C 12V Bell A A - + or Siren B B LED JP4 LED JP4 Delay is started when the door is opened. If the door Used to extend the release time of an access control device remains opened after the time delay has expired the relay or to manually activate a door strike release device. The will turn on and remain on until the door is closed. If the door trigger is activated by a contact closure or a N/O pushbutton is closed before the time delay expires the ELK-960 is reset and the door strike remains activated (door open) after the awaiting another input from the door contact. button is released for the delay time set up in the ELK-960. 12 Volts DC Power Supply 9 USING TWO 960 S TO DELAY THEN THEN TOGGLE A RELAY - + TIME 1 - 60 TIME 1 - 60 ELK-960 ELK-960 SEC SEC Delay Timer Delay Timer MIN MIN TRIGGER TRIGGER + + POLARITY POLARITY REPEAT REPEAT - + - + 1-SHOT 1-SHOT TGR TGR JP5 JP5 END END N/O Hot N/O 120VAC N/O BEGIN Supply BEGIN SWITCH TRIGGER TRIGGER COM K1 COM K1 MODE MODE N/C N/C A A 120V B B LIGHT 1 2 LED JP4 LED JP4 Neutral Used for delaying a trigger then toggling a relay on/off. ELK-960 1 starts a time delay when the N/O switch is closed. When 960 1 s time delay expires, 960 2 is triggered turning it s relay on for the time delay setting , then turning the relay off. (toggle) To sumarize: fire trigger on 1, waits, turns on 2 s relay, waits, then turns relay off. DELAYED ACTIVATION OF ZONE INSTANT ACTIVATION OF ZONE CONTROL PANEL CONTROL PANEL CLOSED 12V AUX WITH INSTANT RESTORAL CLOSED 12V AUX WITH DELAYED RESTORAL ZONE ZONE - + - + TIME 1 - 60 TIME 1 - 60 ELK-960 ELK-960 10 SEC 11 SEC Delay Timer Delay Timer MIN MIN TRIGGER TRIGGER + 22K Ohm + POLARITY POLARITY Resistor REPEAT REPEAT - + - + 1-SHOT 1-SHOT TGR TGR JP5 JP5 END END N/C N/C N/O N/O CONTACT CONTACT BEGIN BEGIN TRIGGER TRIGGER COM K1 COM K1 MODE MODE N/C N/C A A B B LED JP4 LED JP4 Contact closure applies a constant trigger which keeps relay When contact opens, relay is turned on which causes off and zone closed. Delay starts when contact opens. After instant zone violation. Contact reclosure will cancel trigger delay time expires, the relay turns on and the zone is applied by resistor. Delay starts when contact closes. activated (opened). Closing the contact restores the zone Relay turns off and zone restores after delay time expires. instantly. - - - - - -