FTLF1217P2BTL Finisar

Product Specification Fast Ethernet RoHS Compliant Long-Wavelength SFP Transceiver FTLF1217P2xTL PRODUCT FEATURES Up to 200 Mb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions 1310nm LED-based transmitter Duplex LC connector RoHS Compliant and Lead-Free Up to 2km on 62.5/125m MMF APPLICATIONS Metal enclosure, for lower EMI 125 Mb/s 100Base-FX Ethernet / Single 3.3V power supply FDDI Low power dissipation 200 Mb/s ESCON Industrial operating temperature 155 Mb/s Multimode SONET range: -40C to 85C OC-3 SR-0 51 Mb/s Multimode SONET OC-1 SR-0 Finisars FTLF1217P2xTL Small Form Factor Pluggable (SFP) transceivers are 1 compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA) . They are simultaneously compatible with 100Base-FX, FDDI, ESCON, and Multimode 2 SONET OC-3 SR-0 and OC-1 SR-0 standards as specified in IEEE Std 802.3 , ISO/IEC 3 4 5 9314-3 , Enterprise Systems Architecture/390 , and ANSI T1.416.01-1999 , respectively. 4 They are RoHS compliant and lead-free per Directive 2002/95/EC and Finisar Application Note AN-2038. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION FTLF1217P2xTL x W Wide Extraction Bail B Narrow Extraction Bail Finisar Corporation September 13, 2008 Rev. B Page 1 FTLF1217P2xTL Pluggable SFP Product Specification September 2008 I. Pin Descriptions Pin Symbol Name/Description Ref. 1 V Transmitter Ground (Common with Receiver Ground) 1 EET 2 T Transmitter Fault. 2 FAULT 3 T Transmitter Disable. LED output disabled on high or open. 3 DIS 4 MOD DEF(2) Module Definition 2. Data line for Serial ID. 4 5 MOD DEF(1) Module Definition 1. Clock line for Serial ID. 4 6 MOD DEF(0) Module Definition 0. Grounded within the module. 4 7 Rate Select No connection required 8 LOS Loss of Signal indication. Logic 0 indicates normal operation. 5 9 V Receiver Ground (Common with Transmitter Ground) 1 EER 10 V Receiver Ground (Common with Transmitter Ground) 1 EER 11 V Receiver Ground (Common with Transmitter Ground) 1 EER 12 RD- Receiver Inverted DATA out. AC Coupled 13 RD+ Receiver Non-inverted DATA out. AC Coupled 14 V Receiver Ground (Common with Transmitter Ground) 1 EER 15 V Receiver Power Supply CCR 16 V Transmitter Power Supply CCT 17 V Transmitter Ground (Common with Receiver Ground) 1 EET 18 TD+ Transmitter Non-Inverted DATA in. AC Coupled. 19 TD- Transmitter Inverted DATA in. AC Coupled. 20 V Transmitter Ground (Common with Receiver Ground) 1 EET Notes: 1. Circuit ground is internally isolated from chassis ground. 2. T is an open collector/drain output, which should be pulled up with a 4.7k 10k Ohms resistor on FAULT the host board. Pull up voltage should be between 2.0V to Vcc + 0.3V. A high output indicates an LED fault, i.e. LED open or short. Low indicates normal operation. In the low state, the output is pulled to <0.8V. 3. LED output disabled on T >2.0V or open, enabled on T <0.8V. DIS DIS 4. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. MOD DEF(0) pulls line low to indicate module is plugged in. 5. LOS is open collector output. Should be pulled up with 4.7k 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation logic 1 indicates loss of signal. Finisar Corporation September 13, 2008 Rev. B Page 2