17mm FPC / FFC 17mm 0.5 mm Pitch, 1.0 mm above the board Top and Top/Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors FH34(S)Series Increased FPC/FFC holding force Space saving (30 pos. shown) Actuator Metal fittings 1.0mm 3.2mm Easy FPC/FFC insertion Back opening rotating All four sides are chamfered. Top contacts Ready to insert FPC/FFC Features Delivered withDelivered with the actuator openthe actuator open 1. Low-profile With the 1.0 mm above the board and width of 3.8 mm the connectors are used in space saving applications. 2. Increased FPC/FFC retention As compared with existing similar construction connectors: * In horizontal direction: Approximately 2.6 times * In vertical direction: Approximately 2 times 3. Unique Back-Flip rotating actuator FPCFPC The rotating actuator opens from the back of the connector, assuring reliable electrical and mechanical connection. FPC/FFC inserted and retained. 4. Easy FPC insertion and reliable electrical Completed electrical and mechanical connection. connection Proven Flip Lock actuator allows easy insertion of FPC and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 5. Delivered with the actuator open FPC/FPC can be immediately inserted without the need for the opening of the actuator. 6. Accepts standard FPC thickness 0.3mm thick standard Flexible Printed Circuit (FPC) can be used. This is the only ultra-low profile ZIF connector using standard FPC. 7. Compatible with existing connectors. FPC/FFC and PCB mounting patterns are the same as for the FH19SC Series (bottom contact), allowing the use of both connectors for interconnections between two boards or Compatible with existing connectors.(FH19SC SERIES) replacement of the connectors. 8. Conductive traces on the PCB can run under the connector No exposed contacts on the bottom of the connector. 9. Board placement with automatic equipment Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. * 10.Halogen-free *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 1 2013.11w( ) FH34 S Series0.5 mm Pitch, 1.0 mm above the board Top and Top Bottom Contact, Back-Flip actuator Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors Specifications Operating temperature range: Storage temperature range: Current rating 0.5 A (Note 1) -55 to +85C (Note 1) -10 to +50C (Note 2) Ratings Operating humidity range: Storage humidity range: Voltage rating 50 Vrms AC Relative humidity 90% max. (No condensation) Relative humidity 90% max. (No condensation) Recommended FPC/FFC Thickness: 0.3 0.03 mm, Gold plated contact pads Item Specification Conditions 1. Insulation resistance 500 M min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown 250 Vrms AC / one minute 100 m max. 3. Contact resistance 1 mA, AC / DC 20mV max (AC: 1kHz) * Including FPC and FFC conductor resistance Contact resistance: 100 m max. 4. Durability 20 cycles No damage, cracks, or parts dislocation No electrical discontinuity of 1s or longer Frequency: 10 to 55 Hz, single amplitude of 0.75 5. Vibration Contact resistance: 100 m max. mm, 10 cycles in each of the 3 axis No damage, cracks, or parts dislocation No electrical discontinuity of 1s or longer 2 Acceleration of 981m/s , 6 ms duration, sine half- 6. Shock Contact resistance: 100 m max. wave, 3 cycles in each of the 3 axis No damage, cracks, or parts dislocation Contact resistance: 100 m max. 7. Humidity (Steady state) 96 hours at 40C and humidity of 90 to 95% Insulation resistance: 50 M min. No damage, cracks, or parts dislocation Contact resistance: 100 m max. Temperature : -55C / +15C to +35C/+85C / +15C to +35C 8. Temperature cycle Insulation resistance: 50 M min. Time: 30 / 2 to 3 / 30 / 2 to 3 minutes No damage, cracks, or parts dislocation 5 cycles Reflow: At the recommended temperature profile 9. Resistance to soldering heat No deformation of components affecting performance Manual soldering: 350C 5C for 5 seconds (Note 3) Note1: When passing the current through all of the contacts, use 70% of the rated current. Note2: Includes temperature rise caused by current flow. Note3: The termstorag refers to products stored for a long period prior to mounting and use. The operating temperature and humidity range covers the non-conducting condition of installed connectors in storage, shipment or during transportation after board mounting. Materials Part Material Finish Remarks FH34S series Color:Beige LCP FH34SRJ series Color:Gray UL94V-0 Insulator FH34S series PA Color:Black FH34SRJ series LCP(8pos.) FH34SRJ series Color:Black UL94V-0 Contacts Phosphor bronze Gold plating with nickel barrier ------- Metalfittings Phosphor bronze Pure tin reflow plating ------- Ordering information ( ) FH 34S RJ - 30S - 0.5 SH 50 1 2 3 4 5 6 7 1 Series name : FH 6 Termination type 2 SH : SMT horizontal mounting type Series No. : 34S 3 Blank : Top contact 7 Specifications RJ : Top and Bottom contact, halogen-free (50)Standard product 5,000 pieces/reel (Flame retardance UL94V-0). (99)500 pieces/reel 4 Number of positions : 4 to 40 5 Contact pitch : 0.5mm 2