EVAL-M1-099M

AN2016-24 EVAL-M1-05-65D User Manual EVAL-M1-05-65D User Manual iMOTION Modular Application Design Kit About this document Scope and purpose This application note provides an overview of the evaluation-board EVAL-M1-05-65D including its main features, key data, pin assignments and mechanical dimensions. EVAL-M1-05-65D is a complete evaluation-board including a 3-phase IPM for motor drive application. In combination with either EVAL-M1-101T or EVAL-M1-099M it features and demonstrates Infineons IPM technology for motor drive. The evaluation board EVAL-M1-05-65D for Intelligent Power Modules (IPM) was developed to support Customers during their first steps designing applications with CIPOS Micro power modules. Intended audience This application note is intended for all technical specialists working with the EVAL-M1-05-65D board. Table of Contents About this document ....................................................................................................................... 1 Table of Contents ........................................................................................................................... 1 1 Safety precautions ......................................................................................................... 2 2 Introduction .................................................................................................................. 4 3 Main features ................................................................................................................ 5 3.1 Key data ................................................................................................................................................... 6 4 Pin assignments ........................................................................................................... 10 5 Getting Started with EVAL-M1-05-65D ............................................................................. 12 5.1 Setting up the system............................................................................................................................ 12 5.2 iMOTION development tools and software ....................................................................................... 14 5.2.1 MCEWizard setup overview .............................................................................................................. 14 5.2.2 MCEDesigner setup overview .......................................................................................................... 16 6 Schematics and Layout .................................................................................................. 18 6.1 DC-Link Voltage Measurement ............................................................................................................. 18 6.2 Thermistor Output ................................................................................................................................ 19 6.3 EMI input filter and rectifier circuit ....................................................................................................... 19 6.4 Inverter section using CIPOS Micro .................................................................................................... 20 6.5 Power supply ......................................................................................................................................... 21 6.6 Over current circuit ............................................................................................................................... 21 6.7 Layout .................................................................................................................................................... 22 7 Bill of Materials of EVAL-M1-05-65D ................................................................................. 24 8 Reference .................................................................................................................... 26 Revision History ............................................................................................................................ 27 User Manual Please read the Important Notice and Warnings at the end of this document Revision 2.1 www.infineon.com 1 2018-07-09 EVAL-M1-05-65D User Manual iMOTION Modular Application Design Kit Safety precautions 1 Safety precautions In addition to the precautions listed throughout this manual, please read and understand the following statements regarding hazards associated with development systems. Table 1 Precautions Attention: The ground potential of the EVAL-M1-05-65D system is biased to a negative DC bus voltage potential. When measuring voltage waveform by oscilloscope, the scopes ground needs to be isolated. Failure to do so may result in personal injury or death. Darkened display LEDs are not an indication that capacitors have discharged to safe voltage levels. Attention: EVAL-M1-05-65D system contains DC bus capacitors which take time to discharge after removal of the main supply. Before working on the drive system, wait three minutes for capacitors to discharge to safe voltage levels. Failure to do so may result in personal injury or death. Darkened display LEDs are not an indication that capacitors have discharged to safe voltage levels. Attention: Only personnel familiar with the drive and associated machinery should plan or implement the installation, start-up and subsequent maintenance of the system. Failure to comply may result in personal injury and/or equipment damage. Attention: The surfaces of the drive may become hot, which may cause injury. Attention: EVAL-M1-05-65D system contains parts and assemblies sensitive to Electrostatic Discharge (ESD). Electrostatic control precautions are required when installing, testing, servicing or repairing this assembly. Component damage may result if ESD control procedures are not followed. If you are not familiar with electrostatic control procedures, refer to applicable ESD protection handbooks and guidelines. Attention: A drive, incorrectly applied or installed, can result in component damage or reduction in product lifetime. Wiring or application errors such as under sizing the motor, supplying an incorrect or inadequate AC supply or excessive ambient temperatures may result in system malfunction. Attention: Remove and lock out power from the drive before you disconnect or reconnect wires or perform service. Wait three minutes after removing power to discharge the bus capacitors. Do not attempt to service the drive until the bus User Manual 2 Revision 2.1 2018-07-09