PS2401 IXYS

PS2401 AC Power Switch INTEGRATED CIRCUITS DIVISION Description Parameter Rating Units AC Operating Voltage 240 V The PS2401 is an AC Solid State Switch using optical rms Load Current 1 A coupling with dual power SCR outputs to produce an rms On-State Voltage Drop 1.2 V alternative to optocoupler and Triac circuits. The rms (I =1A ) PS2401 switches are robust enough to provide a L rms blocking voltage of up to 500V and max surge P current rating of 20A. In addition, tightly controlled Features zero-cross circuitry ensures switching of AC loads Load Current up to 1A (3A with heat sink) rms rms without the generation of transients. The input and Blocking Voltages up to 500V P output circuits are optically coupled to provide 5mA Sensitivity 3750V of isolation and noise immunity between rms Zero-Crossing Detection control and load circuits. As a result the PS2401 DC Control, AC Output is well suited for industrial environments where Optically Isolated electromagnetic interference would disrupt the TTL and CMOS Compatible operation of electromechanical relays. Low EMI and RFI Generation High Noise Immunity VDE compatible Approvals Machine Insertable, Wave Solderable UL Recognized Component: UL 508 File E69938 CSA Certified Component: File 043639 Applications Programmable Control Ordering Information Process Control Power Control Panels Part Description Remote Switching PS2401 4-Pin (8-Pin Body) SIP Package (25/Tube) Gas Pump Electronics Contactors Large Relays Pin Configuration Solenoids Motors Heaters ZC 1 2 6 8 LED + LED AC Load AC Load DS-PS2401-R14 1 www.ixysic.comPS2401 INTEGRATED CIRCUITS DIVISION Absolute Maximum Ratings 25C Absolute Maximum Ratings are stress ratings. Stresses in Parameter Min Max Units excess of these ratings can cause permanent damage to Blocking Voltage - 500 V P the device. Functional operation of the device at conditions Reverse Input Voltage - 5 V beyond those indicated in the operational sections of this Input Control Current - 100 mA data sheet is not implied. Peak (10ms) - 1 A 1 Input Power Dissipation - 150 mW 2 Total Package Dissipation - 1600 mW Isolation Voltage, Input to Output 3750 - V rms Operational Temperature -40 +85 C Storage Temperature -40 +125 C 1 Derate linearly 1.33 mW / C 2 Derate linearly 16.6 mW / C Electrical Characteristics 25C Parameter Conditions Symbol Min Typ Max Units Output Characteristics AC Operating Voltage I =5mA V 20 - 240 V F OP rms Load Current (Continuous) V =120-240VAC I 0.005 - 1 A L L rms Maximum Surge Current t<16ms I - - 20 A PEAK Off-State Leakage Current V =500V I -- 1 mA L DC LEAK On-State Voltage Drop I =1A - - - 1.2 V L rms rms Critical Rate of Rise - dV/dt 1000 1200 - V/s Switching Speeds Turn-On t - - 0.5 on I =5mA Cycles F Turn-Off t - - 0.5 off 1 st Zero-Cross Turn-On Voltage 1 half-cycle -2 5 V - Subsequent half-cycle - - 1 V Operating Frequency - - 20 - 500 Hz 2 Load Power Factor for Guaranteed Turn-On - PF 0.25 - - - Capacitance Input-To-Output - C -3 - pF I/O Input Characteristics Input Control Current For Normal Environment - -- 5 I mA F For High Noise Environment - - - 10 Input Voltage Drop I =5mA V 0.9 1.2 1.4 V F F Input Dropout Voltage - - 0.8 - - V Reverse Input Current V =5V I - - 10 A R R 1 st Zero Cross 1 half-cycle < 100Hz. 2 Snubber circuits may be required at low power factors. R14 2 www.ixysic.com