Product Information

L-93A7YD-LA53

L-93A7YD-LA53 electronic component of Kingbright

Datasheet
LED; 3mm; yellow; 5-12mcd; 40°; Front: convex

Manufacturer: Kingbright
This product is classified as Large/Heavy, additional shipping charges may apply. A customer service representative may contact you after ordering to confirm exact shipping charges



Price (USD)

5: USD 0.1273 ea
Line Total: USD 0.6365

0 - Global Stock
MOQ: 5  Multiples: 1
Pack Size: 1
Availability Price Quantity
0 - Global Stock


Ships to you between Fri. 05 Apr to Thu. 11 Apr

MOQ : 5
Multiples : 1

Stock Image

L-93A7YD-LA53
Kingbright

5 : USD 0.1273
25 : USD 0.1036
56 : USD 0.0994
100 : USD 0.0922
263 : USD 0.0922

     
Manufacturer
Product Category
Viewing Angle
Led Colour
Led Lens
Mounting
Type Of Diode
Front
Led Diameter
Luminosity
Wavelength
LoadingGif

Notes:- Show Stocked Products With Similar Attributes.
Image Description
KCSA56-104 electronic component of Kingbright KCSA56-104

Display: LED; SMD; 7-segment; 14.22mm; red; 8-26mcd; anode; 0.56
Stock : 1

KPA-1606QBC-G electronic component of Kingbright KPA-1606QBC-G

LED; SMD; 0602; blue; 70-150mcd; 1.6x1.2x0.6mm; 110°; 3.3÷4V; 20mA
Stock : 1

L-1384AL/1ID electronic component of Kingbright L-1384AL/1ID

LED Circuit Board Indicators
Stock : 2

Hot TA12-11EWA electronic component of Kingbright TA12-11EWA

Display: LED; matrix; 5x7; red; 3-8mcd; anode; 39x22.9mm
Stock : 1

DA56-11SRWA electronic component of Kingbright DA56-11SRWA

Display Modules - LED Character and Numeric Red 7-Segment 2 Character Common Anode 1.85V 20mA 0.750" H x 0.984" W x 0.315" D (19.05mm x 25.00mm x 8.00mm) 18-DIP (0.600", 15.24mm)
Stock : 0

KCSC56-105 electronic component of Kingbright KCSC56-105

LED Displays & Accessories
Stock : 0

KCSA04-106 electronic component of Kingbright KCSA04-106

LED Displays & Accessories
Stock : 0

KPL-3015CGCK electronic component of Kingbright KPL-3015CGCK

Standard LEDs - SMD
Stock : 0

WP7113SRSGW electronic component of Kingbright WP7113SRSGW

Standard LEDs - Through Hole T1 3/4 RED/GRN DIFF
Stock : 0

AA4040SF4S-P22 electronic component of Kingbright AA4040SF4S-P22

Infrared Emitters 4x4mm RA IR SMD LED
Stock : 1

Image Description
OSB5SA5111A-CRLED16 electronic component of Optosupply OSB5SA5111A-CRLED16

CRLED; 5mm; blue; 8400mcd; 15°; Front: convex; Pitch:2.54mm
Stock : 1

OSB5SA83C1A electronic component of Optosupply OSB5SA83C1A

LED; 8mm; blue; 100-150mcd; 120°; Front: recessed; Pitch:2.54mm
Stock : 1

Hot CP41B-AHS-CN0Q0354 electronic component of Cree CP41B-AHS-CN0Q0354

Cree, Inc. Standard LEDs - Through Hole Amber LED
Stock : 1

SSL-LX20583ID-FT electronic component of Lumex SSL-LX20583ID-FT

Lumex Standard LEDs - Through Hole LED PMI
Stock : 0

MV8191 electronic component of Everlight MV8191

Standard LEDs - Through Hole T-1 3/4 LED RED DIFF
Stock : 0

C503B-WAN-CBBDB152 electronic component of Cree C503B-WAN-CBBDB152

Standard LEDs - Through Hole White Round
Stock : 1

WP7113SRSGW electronic component of Kingbright WP7113SRSGW

Standard LEDs - Through Hole T1 3/4 RED/GRN DIFF
Stock : 0

TLLR4400-AS12Z electronic component of Vishay TLLR4400-AS12Z

Standard LEDs - Through Hole
Stock : 0

SSL-LX2559D3HD electronic component of Lumex SSL-LX2559D3HD

Standard LEDs - Through Hole LED PMI
Stock : 0

LL-434YD2Q-4C-T electronic component of Lucky Light LL-434YD2Q-4C-T

LED; oval; 3.9x3.2mm; yellow; 780-1300mcd; 110/40°; Front: convex
Stock : 0

Application Notes For Through-Hole LEDs Storage conditions 1. Avoid continued exposure to the condensing moisture environment and keep the product away from rapid transitions in ambient temperature. 2. LEDs should be stored with temperature 30C and relative humidity 60%. 3. Product in the original sealed package is recommended to be assembled within 72 hours of opening. Product in opened package for more than a week should be baked for 30 (+10/-0) hours at 85 ~ 100C. 4. The LED leadframe surface is plated with silver. When the leadframe is stored under high-humidity environments, or exposed to certain chemical elements or gases, the surface may become discolored. Please maintain the cleanliness of the storage environment. 5. If the storage conditions do not meet specification standards, the component pins may become oxidized requiring re-plating and re-sorting before use. Suggest customers consume LEDs as soon as possible, and avoid long-term storage of large inventories. LED MOUNTING METHOD 1. The lead pitch of the LED must match the pitch of the mounting holes on the PCB during component placement. Lead-forming may be required to insure the lead pitch matches the hole pitch. Refer to the figure below for proper lead forming procedures.(Fig. 1) Correct mounting method Incorrect mounting method Note 1-3 : Do not route PCB trace in the contact area between the leadframe and the PCB to prevent short-circuits. Rev No: V18 2/26/2015 Page 1 www.kingbright.com Application Notes For Through-Hole LEDs 2. When soldering wires to the LED, each wire joint should be separately insulated with heat-shrink tube to prevent short-circuit contact. Do not bundle both wires in one heat shrink tube to avoid pinching the LED leads. Pinching stress on the LED leads may damage the internal structures and cause failure. (Fig. 2) 3. Use stand-offs (Fig. 3) or spacers (Fig. 4) to securely position the LED above the PCB. LEAD FORMING PROCEDURES 1. Maintain a minimum of 3mm clearance between the base of the LED lens and the first lead bend. (Fig. 5 and 6) 2. Lead forming or bending must be performed before soldering, never during or after Soldering. 3. Do not stress the LED lens during lead-forming in order to prevent fractures in the epoxy lens and damage the internal structures. 4. During lead forming, use tools or jigs to hold the leads securely so that the bending force will not be transmitted to the LED lens and its internal structures. Do not perform lead forming once the component has been mounted onto the PCB. (Fig. 7) 5. Do not bend the leads more than twice. (Fig. 8) Rev No: V18 2/26/2015 Page 2 www.kingbright.com

Tariff Desc

8541.40.00 54 No .Light emitting diodes (LED), LED displays, optocouplers, photosensitive transistors and diodes, infra-red and fibre optic emitters and detectors Free

8541.10.00 15 No - Diodes, other than photosensitive or light emitting diodes Free

DIODES, TRANSISTORS AND SIMILAR SEMICONDUCTOR DEVICES; PHOTOSENSITIVE SEMICONDUCTOR DEVICES, INCLUDING PHOTOVOLTAIC CELLS WHETHER OR NOT ASSEMBLED IN MODULES OR MADE UP INTO PANELS; LIGHT-EMITTING DIODES (LED); MOUNTED PIEZO-ELECTRIC CRYSTALS:
KBR
KINGBRIGHT
Kingbright Company LLC
Kingbright Corp
Kingbright Corporation
KINGBRIGHT ELECTRONIC

Looking for help? Visit our FAQ's Section to answer to all your questions

 

X-ON Worldwide Electronics

Welcome To X-ON ELECTRONICS
For over three decades, we have been advocating and shaping the electronic components industry. Our management complements our worldwide business scope and focus. We are committed to innovation, backed by a strong business foundation. If you need a trustworthy supplier of electronic components for your business – look no further.
 

Copyright ©2024  X-ON Electronic Services. All rights reserved.
Please ensure you have read and understood our Terms & Conditions before purchasing.
All prices exclude GST.

Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted Image for all the cards that are accepted