WP9294SEC/J3 Kingbright

WP9294SEC/J3 5 mm Round LED Lamp DESCRIPTIONS PACKAGE DIMENSIONS z The Hyper Red device is based on light emitting diode chip made from AlGaInP z Electrostatic discharge and power surge could damage the LEDs z It is recommended to use a wrist band or anti- electrostatic glove when handling the LEDs z All devices, equipments and machineries must be electrically grounded FEATURES z High luminous emission z Low power consumption z General purpose leads z Reliable and rugged z Long life - solid state reliability z RoHS compliant APPLICATIONS z Status indicator z Illuminator z Signage applications z Decorative and entertainment lighting z Commercial and residential architectural lighting Notes: 1. All dimensions are in millimeters (inches). ATTENTION 2. Tolerance is 0.25(0.01 ) unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. Observe precautions for handling 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. electrostatic discharge sensitive devices SELECTION GUIDE 2 1 Iv (mcd) 20mA Viewing A ngle Emitting Color Part Number Lens Type (Material) Min. Typ. 2 1/2 700 1000 Hyper Red WP9294SEC/J3 Water Clear 130 (AlGaInP) *400 *700 Notes: 1. 1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous flux: +/-15%. * Luminous intensity value is traceable to CIE127-2007 standards. Page 1 / 5 2018 Kingbright. All Rights Reserved. Spec No: DSAJ0592 / 1101025073 Rev No: V.8A Date: 06/04/2018 WP9294SEC/J3 ELECTRICAL / OPTICAL CHARACTERISTICS at T =25C A Value Parameter Symbol Emitting Color Unit Typ. Max. Wavelength at Peak Emission I = 20mA Hyper Red 640 - nm F peak 1 Dominant Wavelength I = 20mA Hyper Red 625 - nm F dom Spectral Bandwidth at 50% REL MAX Hyper Red 25 - nm I = 20mA F Capacitance C Hyper Red 27 - pF 2 Forward Voltage I = 20mA V Hyper Red 2.2 2.8 V F F Reverse Current (V = 5V) I Hyper Red - 10 uA R R Notes: 1. The dominant wavelength ( d) above is the setup value of the sorting machine. (Tolerance d : 1nm. ) 2. Forward voltage: 0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. ABSOLUTE MAXIMUM RATINGS at T =25C A Parameter Symbol Value Unit Power Dissipation P 84 mW D Reverse Voltage V 5 V R Junction Temperature T 115 C j Operating Temperature T -40 to +85 C op Storage Temperature T -40 to +85 C stg DC Forward Current I 30 mA F 1 Peak Forward Current I 150 mA FM Electrostatic Discharge Threshold (HBM) 3000 V - 2 Lead Solder Temperature 260C For 3 Seconds 3 Lead Solder Temperature 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity Ref JEDEC/JESD625-A and JEDEC/J-STD-033. Page 2 / 5 2018 Kingbright. All Rights Reserved. Spec No: DSAJ0592 / 1101025073 Rev No: V.8A Date: 06/04/2018