SHC Series Aluminum Electrolytic Capacitors Item Name Rating Case size KNSCHA Lifetime SHC1H100M-0511 SHC50V10F 5*11L 5000 hours 1. Operating Temp. Range -40 + 105 2. Electrical Characteristics Table 1 Nominal Tolerance Dissipation Leakage Permissible Rated Surge Static on Factor Current Ripple Current Voltage Voltage Capacitance Capacitance(%) (tan)max 2min. 20 (mArms)max VDC VDC (F) 20 120Hz 20 120Hz (A)max 105120Hz 50 63 10 -2020 0.10 50 5 3. Dimensions Rubber Bung Sleeve d=0.05 Tinned copper-ply wire d Safety Vent F0.5 6.3 or over D+max D0.5 15min. 4min. L+max. Unit(mm) D+0.5Max L+1Max F0.5 d0.05 5 11 2.0 0.5 Marking 4. Following items are printed with white color on black color sleeve Rated voltage & Nominal Capacitance Example of Marking Polarity (negative) 50V Trade Mark 10F Symbol of Capacitance Tolerance M) Max Operating Temp. KNSCHA SHC (M )105 5.MULTIPLIER FOR RIPPLE CURRENT . Frequency Coefficient Freq.(Hz) 120 300 1K 10K 6050 Cap(F) 0.75 1.00 1.35 1.55 2.00 0.1-47 68-680 0.80 1.00 1.25 1.34 1.50 1000-22000 0.85 1.00 1.10 1.13 1.15 . Temperature Coefficient Ambient 40 60 70 85 105 Temperature() Coefficient 2.40 2.10 1.78 1.65 1.00 No,KNS-20200320004 (1/5)6. Characteristics No. Item Performance Test Method A Protection Resistor : 100010 1 Leakage I= 5.0 (I=0.01CV) I= Max Leakage Current Current Applied Volt : Rated Voltage C=Ctatic Capacitor: V=Rated Voltage Mesauring time : 2minutes Measured Frequency : 120Hz20% 2 8 12 Static F Capacitance Measured Voltage 0.5Vrms, 1.5 2.0VDC 3 Dissiption Factor 0.10 and Under Same as condition of Capacitors (tan) the value specified in Table 1 Test Temp. : 1052 4 High Temp. Leakage Current Applied voltage: Rated voltage Load Cap. Change 20% of initial value Charac- Dissipation Factor 200% of value specified in Table 1 Test Time :2,000 hours teristics Appearance No remarkable abnormality +72, -0 hours the value specified in Table 1 Test Temp. : 1052 5 High Temp. Leakage Current No voltage applied no load Cap. Change 20% of initial value Charac- Dissipation Factor 200% of value specified in Table 1 Test Time :1000 hours teristics Appearance No remarkable abnormality +24, -0 hurs 6 Terminal Tensile Strength 45N 4.5kg Keeping time Strength Bending Strength 25N 2.5kg Tensile 15sec Bending 305sec 7 Impedance W V 50 Ratio Z-25/Z+20 2 Z-40/Z+20 3 8 Temperature Stage Item Performance Stage Test Temp( 202 Charac - 2,3 Impedance Ratio less than the value mentioned in 5-7, 1 -253 teristics 5 Cap, Change 25% against value in stage 4 2 -253 3 202 4 1052 After the capacitor is held at tempereture of each stage 5 202 and reaches temperature stability, measure performance. 6 9 Surge Item Perforemance Voltage Leakage Current the initial specified value Cap, Change 15% against value before test Dissipation Factor the initial specified value Appearance No remakable abnormality Test Temp. 1535 Test volt. Surge Volt.Specified in 2 Voltage apply. 1,000times of chage for 305sec, under frequency of 60.5sec, and discharge for 5min30sec. No,KNS-20200320004 (2/5)