Thyristors Surface Mount 400V - 800V > MAC15 Series Pb MAC15M, MAC15N Description Designed for high performance full-wave AC control applications where high noise immunity and high commutating di/dt are required. Features Blocking Voltage to 800 Industry Standard TO220 Volts Package On-State Current Rating High Commutating di/ of 15 Amperes RMS at dt 9.0 A/ms minimum at 80C 125C Uniform Gate Trigger Operational in Three Currents in Three Modes Quadrants, Q1, Q2, and Q3 High Immunity to dv/ dt 250 V/s minimum at These Devices are 125C PbFree and are RoHS Compliant Minimizes Snubber Networks for Protection Pin Out Functional Diagram MT 2 MT 1 G Additional Information CASE 221A STYLE 4 1 2 Samples Datasheet Resources 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/18/19Thyristors Surface Mount 400V - 800V > MAC15 Series Maximum Ratings (T = 25C unless otherwise noted) J Rating Symbol Value Unit MAC15A6G 600 Peak Repetitive Off-State Voltage (Note 1) V , DRM MAC15-8G 800 V (Gate Open, Sine Wave 50 to 60 Hz, T = -25 to 100C) V J RRM MAC15A8G 800 On-State RMS Current (Full Cycle Sine Wave, 50 to 60 Hz, T = 80C) I 15 A C T (RMS) Peak Non-Repetitive Surge Current I 150 A TSM (One Full Cycle Sine Wave, 60 Hz, T = 125C) C 2 Circuit Fusing Consideration (t = 8.3 ms) I t 93 Asec Peak Gate Power (T = +80C, Pulse Width = 1.0 s) P 20 W C GM Average Gate Power (t = 8.3 ms, T = 80C) P 0.5 W C G(AV) Operating Junction Temperature Range T -40 to +125 C J Storage Temperature Range T -40 to +125 C stg Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. V and V for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage however, positive gate voltage shall not be applied concurrent with negative DRM RRM potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Thermal Characteristics Rating Symbol Value Unit JunctiontoCase (AC) R 2.0 JC Thermal Resistance, C/W JunctiontoAmbient R 62.5 JA Maximum Lead Temperature for Soldering Purposes, 1/8 from case for T 260 C L 10 seconds Electrical Characteristics - OFF (T = 25C unless otherwise noted Electricals apply in both directions) J Characteristic Symbol Min Typ Max Unit - - 0.01 Peak Repetitive Blocking Current T = 25C I , J DRM mA (V = V = V Gate Open) T = 125C I D DRM RRM J RRM - - 2.0 Electrical Characteristics - ON (T = 25C unless otherwise noted Electricals apply in both directions) J Characteristic Symbol Min Typ Max Unit Peak OnState Voltage (Note 2) (I = 21 A Peak) V 1.2 1.6 V TM TM MT2(+), G(+) 5.0 13 35 Gate Trigger Current (Continuous dc) MT2(+), G() I 5.0 16 35 mA GT (V = 12 V, R = 100 ) D L MT2(), G() 5.0 18 35 MT2(+), G(+) 0.5 0.75 1.5 Gate Trigger Voltage (Continuous dc) MT2(+), G() V 0.5 0.72 1.5 V GT (V = 12 V, R = 100 ) D L MT2(), G() 0.5 0.82 1.5 MT2(+), G(+) 33 50 Latching Current MT2(+), G() V 36 80 V GD (V = 24 V, I = 35 mA) D G MT2(), G() 33 50 Holding Current (V = 12 V , Gate Open, Initiating Current = 200 mA)) I 20 40 mA D dc H Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be indicated by the Electrical Characteristics if operated under different conditions. 2. Indicates Pulse Test: Pulse Width 2.0 ms, Duty Cycle 2%. 2019 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 06/18/19