X-On Electronics has gained recognition as a prominent supplier of MCP19110-E/MJ Switching Controllers across the USA, India, Europe, Australia, and various other global locations. MCP19110-E/MJ Switching Controllers are a product manufactured by Microchip. We provide cost-effective solutions for Switching Controllers, ensuring timely deliveries around the world.
We are delighted to provide the MCP19110-E/MJ from our Switching Controllers category, at competitive rates not only in the United States, Australia, and India, but also across Europe and beyond. A long established and extensive electronic component distribution network has enhanced our global reach and dependability, ensuring cost savings through prompt deliveries worldwide. Client satisfaction is at the heart of our business, where every component counts and every customer matters. Our technical service team is ready to assist you. From product selection to after-sales support, we strive to deliver a seamless and satisfying experience. Are you ready to experience the best in electronic component distribution? Contact X-ON Electronics today and discover why X-On are a preferred choice for the MCP19110-E/MJ and other electronic components in the Switching Controllers category and beyond.
MCP19110/11 Digitally-Enhanced Power Analog Controller with Integrated Synchronous Driver Synchronous Buck Features Microcontroller Features Precision 8 MHz Internal Oscillator Block: Input Voltage: 4.5V to 32V - Factory Calibrated Output Voltage: 0.5V to 3.6V Interrupt Capable - Greater than 3.6V requires external divider -Firmware Switching Frequency: 100 kHz to 1.6 MHz - Interrupt-on-Change Pins Quiescent Current: 5 mA Typical Only 35 Instructions to Learn High-Drive: 4096 Words On-Chip Program Memory - +5V Gate Drive High Endurance Flash: - 1A/2A Source Current - 100,000 write Flash Endurance - 1A/2A Sink Current - Flash Retention: >40 years Low-Drive: Watchdog Timer (WDT) with Independent - +5V Gate Drive Oscillator for Reliable Operation - 2A Source Current Programmable Code Protection - 4A Sink Current In-Circuit Debug (ICD) via Two Pins (MCP19111) Peak Current Mode Control In-Circuit Serial Programming (ICSP) via Two Differential Remote Output Sense Pins Multi-Phase Systems: 11 I/O Pins and One Input-Only Pin (MCP19110) - Master or Slave - Three Open-Drain Pins - Frequency Synchronized 14 I/O Pins and One Input-Only Pin (MCP19111) - Common Error Signal - Three Open-Drain Pins Multiple Output Systems: Analog-to-Digital Converter (ADC): - Master or Slave - 10-bit Resolution - Frequency Synchronized - 12 Internal Channels - AEC-Q100 Qualified - Eight External Channels Configurable Parameters: Timer0: 8-bit Timer/Counter with 8-Bit Prescaler - Overcurrent Limit Enhanced Timer1: - Input Undervoltage Lockout - 16-bit Timer/Counter with Prescaler - Output Overvoltage - Two Selectable Clock Sources - Output Undervoltage Timer2: 8-Bit Timer/Counter with Prescaler - Internal Analog Compensation - 8-bit Period Register 2 - Soft Start Profile I C Communication: - Synchronous Driver Dead Time - 7-bit Address Masking - Switching Frequency - Two Dedicated Address Registers Thermal Shutdown TM - SMBus/PMBus Compatibility 2013-2016 Microchip Technology Inc. DS20002331D-page 1MCP19110/11 Pin Diagram 24-Pin QFN (MCP19110) 1 GPA0 V 18 DD 2 BOOT GPA1 17 3 GPA2 16 HDRV MCP19110 4 GPA3 15 PHASE 5 GPA7 V 14 DR EXP-25 6 GPA6 13 LDRV DS20002331D-page 2 2013-2016 Microchip Technology Inc. GPA5/MCLR 7 GPB2 24 GPA4 8 GPB1 23 9 GPB0 -V 22 SEN 10 GND 21 +V SEN V 11 +I 20 IN SEN 12 P 19 -I GND SEN
Understanding active and passive electronic components is fundamental to the field of electronics. Active components, such as transistors and ICs, provide amplification and control, while passive components, like resistors and capacitors, shape a